Eaton Champ MLLA M2 Series Installation & Maintenance Information

IF 1946 • 09/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 2INSTALLATIONA. M2-FLUSH-MT-KIT1. Make sure the power is disconnected to the conduit system beforeinstalling the luminaire.2. Install flush mount brackets to rear of luminaire driver housing usingthe provided two (2) 1/4” hex bolts and split ring lock washers for eachbracket. Bracket orientation as shown in Figure 1. Torque to 64 in.-lbs (7.2N-m)3. Identify mounting location suitable for supporting luminaire, mark and drillholes for flush brackets per dimensions shown in Figure 1.4. Luminaire is now ready for mounting. It is strongly suggested to usetwo (2) qualified tradespeople to proceed with the final mounting of theluminaire. This is recommended to avoid any personal injury or damage tothe luminaire.5. Install and tighten four (4) 1/4” diameter fasteners (customer supplied) inbracket mounting holes. It is recommended that stainless steel hardwarebe used in locations with corrosion concerns.Figure 1. Flush Ceiling Mount Installation! WARNINGTo avoid injury to personnel, do not let the luminaire hang or flex on onebracket at a time. Failing to comply will result in breakage of bracket andpossible injury or death.Length 2 Foot(in)2 Foot(mm)4 Foot(in)4 Foot(mm)A 24.0 610 39.0 991B 24.25 616 24.25 616C 2.50 63.5 2.50 63.5THIRD ANGLE PROJECTIONBCA66026.0A123.24.85175.36.901/4-20 x 1/2" HEX HEAD BOLT1/2" SPLIT LOCK WASHERZONE NO. DESCRIPTION DATE APPRD. LTR. NO.CCHSY-SW-Template-D SW_REV 11/2015DO NOT SCALE DRAWINGNOTES:1.ABCD12345678ADCB8 7 6 5 4 3 2 1Your nameASSY2 CAT2CAT1ASSY1ARE INMILLIMETERS.DIMENSIONS IN [ ] ARE INALL PRIMARY DIMENSIONSUNLESS OTHERWISE SPECIFIED,MM/DD/YYYYYour NameWITH ASME Y14.5 2009.DIM AND TOL IN ACCORDANCE±±±±.1 .3 INCHES.rev0000000WT. 15.84 LBSCALE 1:2FIRST MADE FOR Catalog FamilyTitle Line 1APPROVED BYDRAWN BYFinish... THICKMaterialmmin..13.0001.5Your NameTHIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL ANDTRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEYANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICHIT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESSWRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOANAND IS TO BE RETURNED UPON REQUEST.Title Line 2Your NameMM/DD/YYYY1.5±.005±.01±±ANGLES.XXX.XX.XREDRAWN DATEORIGINAL DATEUNLESS OTHERWISE SPECIFIEDTOLERANCESMATERIAL:FINISH:APPROVED BYCHECKED BYUSED ONAPPLICATIONNEXT ASSY.TITLECODE IDENT. NO.SIZE REV.D SHEET 1 OF 5CODE ...THIRD ANGLE PROJECTIONBCA1/4-20 x 1/2" HEX HEAD BOLT1/2" SPLIT LOCK WASHERZONE NO. DESCRIPTION DATE APPRD. LTR. NO.DO NOT SCALE DRAWING12345ADCB5 4 3 2 1Your nameASSY2 CAT2CAT1ASSY1ARE INMILLIMETERS.DIMENSIONS IN [ ] ARE INALL PRIMARY DIMENSIONSUNLESS OTHERWISE SPECIFIED,MM/DD/YYYYYour NameWITH ASME Y14.5 2009.DIM AND TOL IN ACCORDANCE±±±±.1 .3 INCHES.rev0000000WT. 15.84 LBSCALE 1:2FIRST MADE FOR Catalog FamilyTitle Line 1APPROVED BYDRAWN BYFinish... THICKMaterialmmin..13.0001.5Your NameTHIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL ANDTRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEYANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICHIT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESSWRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOANAND IS TO BE RETURNED UPON REQUEST.Title Line 2Your NameMM/DD/YYYY1.5±.005±.01±±ANGLES.XXX.XX.XREDRAWN DATEORIGINAL DATEUNLESS OTHERWISE SPECIFIEDTOLERANCESMATERIAL:FINISH:APPROVED BYCHECKED BYUSED ONAPPLICATIONNEXT ASSY.TITLECODE IDENT. NO.SIZE REV.D SHEET 1 OF 5CODE ...INSTALLATIONMax. mounting height of 25.2 ft (7.68m)B. M2-CEILING-WALL-KT1. Make sure the power is disconnected to the conduit system beforeinstalling the luminaire.2. Mark and drill holes for fastening end brackets. Use two (2) 1/4” diameterfasteners (customer supplied) at center to center measurements (seeFigure 2). It is recommended that stainless steel hardware be used inlocations with corrosion concerns.3. Luminaire is now ready for mounting. It is strongly suggested to usetwo (2) qualified tradespeople to proceed with the final mounting of theluminaire. This is recommended to avoid any personal injury or damage tothe luminaire.4. For end mount wall/ceiling mounting brackets, it is recommended tomount one bracket first and then, while supporting the luminaire, insert itinto the mounted bracket, then attach the other bracket.5. Aim the luminaire to achieve desired light output and tighten the 1/4” setscrews on brackets. Torque to 64 in.-lbs. (7.2 N-m).6. Use set screw to limit rotation of the luminaire.Figure 2. Ceiling-Wall Mount InstallationLength 2 Foot(in)2 Foot(mm)4 Foot(in)4 Foot(mm)A 28.5 724 28.5 724B 24.0 610 39.0 991! WARNINGTo avoid injury to personnel, do not let the luminaire hang or flex on onebracket at a time. Failing to comply will result in breakage of bracket andpossible injury or death.THIRD ANAB175.36.90205.28.0863.52.50542.13B72328.5CCHSY-SW-Template-D SW_REV 11/2015NOTES:1.ABCD3456788 7 6 5 4 3ASSY2 CAT2CAT1ASSY1WITH ADIM AND TOFinish... THICKMaterialTHIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL ANDTRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEYANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICHIT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESSWRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOANAND IS TO BE RETURNED UPON REQUEST.ANGLES.XXX.XX.XUNLESS OTOMATERIAL:FINISH:USED ONAPPLICATIONNEXT ASSY.CODE ...