Eaton Champ MLLA M2 Series Installation & Maintenance Information

IF 1946 • 09/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 4E. PENDANT MOUNT INSTRUCTIONS1. Make sure the power is disconnected from the conduit system beforeinstalling the luminaire2. For Pendant Mount the conduit should be located in line with the 3/4”NPT entry on the rear of the luminaire driver housing (see Figure 6).3. Luminaire is ready for mounting. It is strongly suggested to use two (2)qualified tradespeople to proceed with the final mounting of the luminaire.This is recommended to avoid any personal injury or damage to theluminaire.4. Verify sufficient quantity of Eaton’s STL thread lubricant is on conduitentries and that all unused conduit entries on the end caps are closedwith lubricated plugs (see Figure 13).5. Engage threaded conduit in rear driver housing NPT entry and fully tightenin to desired position for operations (engage at least 3-1/2 threads).6. Tighten set screws on driver housing as shown in Figure 8. Torque setscrews to 20 in-lb (2.3 N-m).7. Luminaire now ready to make electrical connections. See section titledWiring The LED Luminaire for detailed instructions.Length 2 Foot(in)2 Foot(mm)4 Foot(in)4 Foot(mm)A 24.0 610 39.0 991Figure 6. Pendant Mount Detail ViewFigure 7. Pendant Mount Set Screw DetailTHIRD ANGLE PROJECTIONATHREADED CONDUIT(3/4" NPT STANDARD)175.36.90112.94.45DO NOT SCALE DRAWINGNOTES:1.12345678ADCB8 7 6 5 4 3 2 1Your nameASSY2 CAT2CAT1ASSY1ARE INMILLIMETERS.DIMENSIONS IN [ ] ARE INALL PRIMARY DIMENSIONSUNLESS OTHERWISE SPECIFIED,MM/DD/YYYYYour NameWITH ASME Y14.5 2009.DIM AND TOL IN ACCORDANCE±±±±.1 .3 INCHES.rev0000000WT. 15.84 LBSCALE 1:2FIRST MADE FOR Catalog FamilyTitle Line 1APPROVED BYDRAWN BYFinish... THICKMaterialmmin..13.0001.5Your NameTHIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL ANDTRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEYANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICHIT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESSWRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOANAND IS TO BE RETURNED UPON REQUEST.Title Line 2Your NameMM/DD/YYYY1.5±.005±.01±±ANGLES.XXX.XX.XREDRAWN DATEORIGINAL DATEUNLESS OTHERWISE SPECIFIEDTOLERANCESMATERIAL:FINISH:APPROVED BYCHECKED BYUSED ONAPPLICATIONNEXT ASSY.TITLECODE IDENT. NO.SIZE REV.D SHEET 5 OF 5CODE ...THIRD ANGLE PROJECTIONTHREADED CONDUIT(3/4" NPT STANDARD)DO NOT SCALE DRAWING123ADCB3 2 1Your nameASSY2 CAT2CAT1ASSY1ARE INMILLIMETERS.DIMENSIONS IN [ ] ARE INALL PRIMARY DIMENSIONSUNLESS OTHERWISE SPECIFIED,MM/DD/YYYYYour NameWITH ASME Y14.5 2009.DIM AND TOL IN ACCORDANCE±±±±.1 .3 INCHES.rev0000000WT. 15.84 LBSCALE 1:2FIRST MADE FOR Catalog FamilyTitle Line 1APPROVED BYDRAWN BYFinish... THICKMaterialmmin..13.0001.5Your NameTHIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL ANDTRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEYANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICHIT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESSWRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOANAND IS TO BE RETURNED UPON REQUEST.Title Line 2Your NameMM/DD/YYYY1.5±.005±.01±±ANGLES.XXX.XX.XREDRAWN DATEORIGINAL DATEUNLESS OTHERWISE SPECIFIEDTOLERANCESMATERIAL:FINISH:APPROVED BYCHECKED BYUSED ONAPPLICATIONNEXT ASSY.TITLECODE IDENT. NO.SIZE REV.D SHEET 5 OF 5CODE ...SECONDARY SUPPORTIf using secondary support, attach one end of the support cable to one of thefour (4) attachment points provided on the luminaire driver housing and securethe other end to a fixed support. Use a minimum of two (2) support cables perluminaire, securing a single cable at two (2) locations on the exterior of theluminaire driver housing.Arrange the secondary support cables to limit the suspended vertical distanceto no more than 18 inches from the primary mounted position. Cables mustbe installed in this manner to limit the potential vertical drop to 18 inchesmaximum.PUSH-TO-TEST SWITCHA remote push-to-test switch (not supplied) suitable for the classified areamust be wired in the supply circuit to periodically test the emergency operationfeature (see wiring diagrams). The switch used must be suitable for the areaclassifications.STATUS INDICATOR LIGHTThe status indicator light located on LED board (Red LED) will be “ON“when the battery is charging. If the status LED is flashing, replaceemergency driver unit.. If required customer can remote mount their ownstatus indicator light with suitable electrical ratings. Contact Eaton’sCrouse-Hinds for additional support.For remote mounting of Status Indicator light refer to figure below “Remotemounting Test switch & Status indicator”.Important instructions for remote mounting of push to test switch (customersupplied):a. Switch shall be installed using acceptable wiring methods for the areasinvolved in accordance with the NEC.b. Switch shall be connected to the emergency luminaire circuit such thatwhen depressed it provides a transfer function and disconnects andisolates the normal input from the emergency input.c. Switch shall be identified as to its function (i.e. – marked “EmergencyLuminaire Test Switch”).d. Switch shall have electrical ratings suitable for the emergency luminaires.e. Switch shall be manually operated type.f. Switch shall be of Momentary-contact type.g. Switch must be visible and accessible without the use of tools.Figure 8 Remote mounting test switch and status indicatorEMERGENCY DRIVER UNIT INFORMATIONCHAMP Emergency Linear LED luminaires are supplied with an emergencydriver unit. Disconnect the battery converter connector (Red-Red wires)prior to performing maintenance (Refer to Figures 14A, 14B or 14C). This willdisconnect the charged battery from the LEDs. The emergency driver unit mustbe checked periodically to ensure that it is working properly.IMPORTANT INSTRUCTIONS (for customer supplied wall switch)1. Installations in which a remote wall switch is to be used, connect anunswitched supply line to the Black wire (L) and a switched supply line tothe White/Red wire (L1) of the Emergency Backup Module. Refer to wallswitch connection details on Wiring Diagrams in Figures 14A, 14B and14C.2. When the switched supply line (L1) is de-energized using the wall switch,the luminaire will turn off light output while the battery circuit remainsactive and charging.3. Upon the loss of line power to the Emergency BackupModule, theluminaire will immediately operate in Emergency Operations mode(automatic switching) with a reduced light output .4. If the unswitched supply line is connected to Black wire (L) only, batterywill charge, and luminaire will be in OFF condition (i.e AC driver is not inoperating condition). This is the Emergency Operations Only mode andthe luminaire shall only be illuminated on the loss of the line power.5. If a wall switch is to be installed in a hazardous (classified) area, the switchused must be rated for the area classification.6. The wall switch used shall be suitable for 120 - 277VAC and ≥15Aoperations.Threaded conduit - 3/4" NPTstandard (not provided byEaton’s Crouse-Hinds)