5-42 L60 Line Phase Comparison Relay GE Multilin5.2 PRODUCT SETUP 5 SETTINGS5If the PUSHBTN 1 MESSAGE is set to “Normal”, the message programmed in the PUSHBTN 1 ID and PUSHBTN 1 ON TEXTsettings will be displayed as long as PUSHBUTTON 1 ON operand is asserted, but not longer than time period specifiedby FLASH MESSAGE TIME setting. After the flash time is expired, the default message or other active target message isdisplayed. The instantaneous reset of the flash message will be executed if any relay front panel button is pressed orany new target or message becomes active.The PUSHBTN 1 OFF TEXT setting is linked to PUSHBUTTON 1 OFF operand and will be displayed in conjunction withPUSHBTN 1 ID only if pushbutton element is in the “Latched” mode. The PUSHBTN 1 OFF TEXT message will be displayedas “Normal” if the PUSHBTN 1 MESSAGE setting is “High Priority” or “Normal”.• PUSHBUTTON 1 EVENTS: If this setting is enabled, each pushbutton state change will be logged as an event intoevent recorder.The user-programmable pushbutton logic is shown below.Figure 5–6: USER-PROGRAMMABLE PUSHBUTTON LOGICUser-programmable pushbuttons require a type HP relay faceplate. If an HP type faceplate was ordered separately,the relay order code must be changed to indicate the correct faceplate option. This can be done via EnerVista URSetup with the Maintenance > Enable Pushbutton command.SETTINGPUSHBUTTON 1FUNCTIONDisabledLatchedSelf-ResetSETTINGPUSHBTN 1 SETOff (FlexLogic operand)SETTINGPUSHBTN 1 RESETOff (FlexLogic operand)SETTINGPUSHBTN 1 LOCALOff (FlexLogic operand)SETRSTFLEXLOGIC OPERANDPUSHBUTTON 1 ONFLEXLOGIC OPERANDPUSHBUTTON 1 OFFFLEXLOGIC OPERANDPUSHBUTTON 1 OFFFLEXLOGIC OPERANDPUSHBUTTON 1 ONSETTINGPUSHBTN 1 AUTORSTDisabledEnabledDELAY0SETTINGPUSHBTN 1 DROP-OUTTIME0SETTINGPUSHBTN 1 MESSAGEDisableHigh PriorityNon Volatile LatchPB1LEDFLEXLOGIC OPERANDPUSHBUTTON 1 ONFLEXLOGIC OPERANDPUSHBUTTON 2 ONFLEXLOGIC OPERANDFLEXLOGIC OPERANDPUSHBUTTON 12 ONPUSHBUTTON 3 ONFLEXLOGIC OPERANDANY PB ONNormalSETTINGPUSHBTN 1 ID TEXTLCD MESSAGEPUSHBTN 1 OFF TEXTXXXXXXXXXXXXXXXXXXXXENGAGE MESSAGESETTINGFLASH MESSAGETIME0SETTINGPUSHBTN 1 REMOTEOff (FlexLogic operand)50msec0msec50msec0msec200msec0msec200msec0msecINSTANTANEOUSRESET *SETTINGFLASH MESSAGETIME0see PRODUCT SETUP> DISPLAY PROPERTIES menuINSTANTANEOUSRESET *ORLCD MESSAGEENGAGE MESSAGETHE MESSAGE IS TEMPORARILY REMOVED IFANY KEYPAD BUTTON IS PRESSED. TEN(10)SECONDS OF KEYPAD INACTIVITY RESTORESTHE MESSAGE* INSTANTANEOUS RESET WILL BE EXECUTED IF ANY RELAY FRONTPANEL BUTTON IS PRESSED OR ANY NEW TARGET OR MESSAGE1. IF PUSHBUTTON 1 LED CONTROL IS SET TO OFFPB1LEDSETTINGPUSHBTN 1 LED CTLANY FLEXLOGIC2. IF PUSHBUTTON 1 LED CONTROL IS NOT SET TO OFFFLEXLOGIC OPERANDPUSHBUTTON 1 ONPUSHBUTTON 1 LED LOGICANDLATCHPUSHORORANDORORORORORORANDANDANDANDANDANDANDANDANDSETTINGANDtPKPt RSTt RSTt RSTPUSHBTN 1 AUTORSTsee PRODUCT SETUP> DISPLAY PROPERTIES menuSETTINGPUSHBTN 1 ID TEXTPUSHBTN 1 ON TEXTXXXXXXXXXXXXXXXXXXXXBECOMES ACTIVE.OPERAND842021A1.DWGNOTE
