Garland THE MASTER Installation And Operation Manual

Also see for THE MASTER: Installation and operation manual Original user manual

Contents

Part # 1955203 Rev2 (12/07/10) Page 131. Press and hold PROG key for three (3) seconds – all theproduct key LEDS light.2. Code will be displayed. The controller is asking for theaccess code. Press 4-2-7-5 and theSTART/CANCEL key. PROD will be displayed indicatingyou have gained access to Product Programming.3. Press the product key (1-9) into which you want to storea cooking program. SHLF will be displayed. The controlis asking if you want to program the key as a shelf timeror with a cooking profile. Select your answer by pressingthe START/CANCEL key. When the correct answer isdisplayed press the SET key. The TIME LED will light. 30:00will be displayed.4. Set first cook time using dial. If more than one cookingprofile is desired:• Press the product key where the program is to bestored (1-9) – PR-2 will be displayed.• Set the second cook time using the dial (factorypresets for PR-2 through PR-5 are :00).• Press the same product key (1-9 again – PR-3 will bedisplayed.• Repeat the process for all profiles. When the lastprofile time has been entered, press the SET key ORIf less than five (5) profiles are desired press the SET key afterthe last required profile – PRE will be displayed, followedby :00. The controller is asking if you would like a reminderalarm (pre-alarm) to sound during the cooking process(factory preset is :00).5. If a pre-alarm signal is desired – dial in the time thatthe alarm is to sound. (Ex. If the product is to be turnedhalfway through the 60 minute cooking cycle, set thepre-alarm to 30 minutes. If pre-alarm is not desired verifythat “:00” is displayed. Press the SET key – TEMP LED willlight, and the display will show the first profile cookingtemperature (factory preset to 350°F).6 Set the first cooking temperature using the dial.• Press the product key – PR-2 will be displayedfollowed by the second temperature.• Set the second cooking temperature using the dial.• Repeat as you did for cooking time, for all theprofiles desired.OPERATING INSTRUCTIONS ContinuedNOTE: the controller will only accept cooking temperaturesfor the number of profiles for which a cooking time has beenset. If the product key is pressed after the last programmedprofile, the first temperature will be displayed.• Press SET after the last cooking temperatures hasbeen entered, HOLD will be displayed.7. Use the START/CANCEl key to select yes or no. Press theSET key.8. If yes was selected, the HOLD LED will light. Enter thehold temperature using the dial. (factory preset at 200°F)Press the SET key, FAN will be displayed and the FAN LEDwill light.• Set the fan speed desired for the first cooking profileusing the individual fan keys (HIGH, LOW or PULSE),press the product key and set the fan speed for thesecond cooking profile. Continue until all the profileshave been assigned a fan speed. Press the SET keywhen complete. As with the temperature, if theproduct key is pressed after the last programmedprofile, the first fan speed will be displayed.9. FL or ST will be displayed (for flex time or straight time)(factory preset for flex time). Select flex or straight timeusing the START/CANCEL key for the first profile. Pressthe product key and select straight time or flex time forthe second profile. Continue until all the profiles havebeen assigned straight or flex time. Press the SET keywhen complete. If the product key is pressed after the lastprogrammed profile, the first profile will be displayed.10 Programming for that product key is complete.Cooking Using The Product Keys(Master 475)1. On initial start-up, press the product key for the menuitem to be cooked. Wait until Load is displayed.2. Load the oven.3. Press the product key for the loaded menu item.4. Press the START/CANCEL, key.5. To cancel the alarm or the holding operation, press theSTART/CANCEL key followed by the product key.