Garmin RV-BBT600 Series Owner's Manual
Also see for RV-BBT600 Series: Installation instructions
                          | |
Contents
| 
Power input type Vehicle power using RV-BBT600 series dock oran approved mount accessory and vehiclepower cable. AC power using an optionalaccessory for home or office use only.Battery type Rechargeable lithium-ion, 3.7 VdcInput Maximum DC 5 V, 2 AWireless protocols 2.4 GHz Bluetooth wireless technology2.4 GHz Wi‑Fi technologyAppendixMounting and Powering the Device in anAutomobileWARNINGThis product contains a lithium-ion battery. To prevent thepossibility of personal injury or product damage caused bybattery exposure to extreme heat, store the device out of directsunlight.Both the device and its mount contain magnets. Under certaincircumstances, magnets may cause interference with someinternal medical devices, including pacemakers and insulinpumps. Keep the device and its mount away from such medicaldevices.NOTICEBoth the device and its mount contain magnets. Under certaincircumstances, magnets may cause damage to some electronicdevices, including hard drives in laptop computers. Use cautionwhen the device or its mount is near electronic devices.The RV HUB remote can operate independently as a full-featured navigation device. You can use an optional automobilemount accessory to mount the remote in another vehicle. This isuseful when your RV is parked and you are using an automobileto travel locally. Go to buy.garmin.com to purchase accessories.1 Plug the vehicle power cable À into the USB port on theautomobile mount.2 Press the mount Á onto the suction cup  until it snaps intoplace.The Garmin logo on the mount should face right-side up.3 Press the suction cup to the windshield, and flip the lever Ãback toward the windshield.4 Place the back of the device onto the magnetic mount.5 Plug the other end of the vehicle power cable into a poweroutlet in your vehicle.6 Switch the RV HUB remote to the Car vehicle profile (VehicleProfiles, page 6).Installing a Memory Card for Maps and DataYou can install a memory card to increase the storage space formaps and other data on your device. You can purchase memorycards from an electronics supplier, or go to www.garmin.com/maps to purchase a memory card with pre-loaded Garminmapping software. The device supports microSD memory cardsfrom 4 to 32 GB.1 Locate the map and data memory card slot on your device(RV HUB Remote Overview, page 1).2 Insert a memory card into the slot.3 Press it in until it clicks.Purchasing Additional Maps1 Go to your device product page at garmin.com.2 Click the Maps tab.3 Follow the on-screen instructions.Purchasing AccessoriesGo to garmin.com/accessories.Connecting to Scheiber™ Controls andSensorsIf your RV includes a Scheiber system or modules, you can usethe included Xperience™ app to view sensor data and interactwith control modules in your Scheiber system.1 Connect your Scheiber interface module to the CAN 2CAN bus port on the back of your RV HUB dock.This is usually performed by a professional installer. Therequired cables and adapters are provided with yourScheiber system. For more information about the location ofthe CAN 2 port, see the installation instructions for yourRV HUB stereo.2 On the RV HUB remote, select Music > > Settings >Scheiber Enabled to activate the Xperience app.3 On the RV HUB remote, select > Xperience to launch theXperience app and interact with your Scheiber system.NOTE: The Xperience app is not available when the RV HUBremote is in the RV HUB dock.TroubleshootingMy remote cannot control the dockThe remote controls the dock using a wi-fi connection. If youcannot control the dock playback using the remote, you can trythese options to connect the devices.• Remove the remote from the dock and place in back into inthe dock (Docking the RV HUB Remote, page 1).Each time you place the remote in the dock, it receives thewi-fi connection information from the dock and connectsautomatically.• Verify the dock is receiving power.The remote cannot connect to the dock when it is turned off.• If the dock is in station mode, verify the selected wi-fi networkis available (Connecting the Dock and Remote to a Wi-FiNetwork, page 16).If the dock cannot connect to the selected Wi-Fi networkwhile it is in station mode, it cannot create a connection to theremote. If no Wi-Fi network is available, you should set thedock to access point mode (Access Point Settings, page 16).• Manually connect the remote to the dock access point(Connecting the Remote to the Dock Manually, page 16).My device is not acquiring satellite signals• Verify the GPS simulator is turned off (Navigation Settings,page 15).• Take your device out of parking garages and away from tallbuildings and trees.• Remain stationary for several minutes.Appendix 19 |
This manual is suitable for:
manualsdatabase
Your AI-powered manual search engine