Contents - October
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Manifold Component Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Section 3 Repair Procedures
- repair procedures
- Platform Controls
- Joysticks
- How to Adjust the Joystick Max-out Setting
- How to Adjust the Joystick Ramp Rate Setting
- How to Adjust the Joystick Threshold Setting
- How to Calibrate the Boom Angle Sensor
- Platform Components
- Platform Leveling Slave Cylinder
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Overload System
- Jib Boom Components
- Jib Boom Lift Cylinder
- Boom Components
- How to Repair the Cable Track
- How to Remove the Boom
- Boom Lift Cylinder
- Boom Extension Cylinder
- Boom Extend/Retract Cables
- How to Replace the Boom Extend/Retract Cables
- Platform Leveling Master Cylinder
- Engines
- How to Install the Flex Plate
- How to install the Pump and Bell Housing Assembly
- Ground Controls
- Hydraulic Pumps
- Drive Pump
- How to Prime the Pump
- Valve Adjustments - Function Manifold
- How to Adjust the Boom Extend Relief Valve
- Brake/Two-Speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- Fuel and Hydraulic Tanks
- Hydraulic Tank
- How to Remove the Turntable Rotation Hydraulic Motor
- How to Adjust the Turntable Rotation Gear Backlash
- turntable rotation components
- Steer Axle Components
- Drive Motors
- Steer Cylinders
- Non-steer Axle Components
- Oscillating Axle Components
- Oscillate Directional Valve
- How to Set Up the Directional Valve Linkage
- Section 4 Fault Codes
- Control System Fault Codes
- Fault Code Display - Deutz and Perkins Models
- F-22 Models
- Main Menu Structure - Deutz D 2.9 L4 Models
- Main Menu Structure - Perkins 404F-22 Models
- Deutz D 2.9 L4 Engine Fault Codes
- Perkins 404F-22 Engine Fault Codes
- Continental TME27 Engine Fault Codes
- Section 5 Schematics
- Electrical Symbol Legend
- Hydraulic Symbols Legend
- Relay and Fuse Panel Legend - Deutz TD2011L04i
- Relay and Fuse Panel Legend - Perkins 804D-33
- Connector Pin Legends
- Continental TME27 Engine Harness
- S-80X Ground Control Box Wiring Diagram
- Deutz TD2.9 L4 Engine Harness
- Perkins 404F-22T Engine Harness
- Electrical Schematic, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA)
- Ground Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Platform Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (CE)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (AS)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- Platform Level Cutout, CTE Option
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Hydraulic Schematics
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
|
October 2016 Service and Repair ManualPlatform ControlsPart No. 1269074 S-80 • S-85 • S-80X 21How to Adj ust the Joystic k Ramp R ate SettingHow to Adjust the Joystick RampRate SettingThe ramp rate setting of a joystick controls the timeat which it takes for the joystick to reach maximumoutput, when moved out of the neutral position. Theramp rate settings of a joystick can be changed tocompensate for hydraulic pump wear to maintainpeak performance from the machine.Note: Perform this procedure with the boom in thestowed position.1 Pull out the red Emergency Stop button to theon position at both the ground and platformcontrols.2 Turn the key switch to platform control. Do notstart the engine.3 Push in the platform controls red EmergencyStop button to the off position.4 Do not press down the foot switch.5 Move and hold the drive enable toggle switchin the right position and pull out the redEmergency Stop button to the on position.6 When the alarm sounds, release the driveenable toggle switch.7 Momentarily activate the drive enable toggleswitch in the right direction 6 times.Result: There should be a pause and the alarmshould sound 6 times indicating that themachine is in ramp rate calibration mode.8 Start the engine from the platform controls andpress down the foot switch.9 Start a timer and simultaneously move thejoystick in either direction full stroke. Note howlong it takes the function to reach maximumspeed. This is the ramp rate.10 Compare the function ramp rate time with thetable below and determine whether the ramprate time needs to increase or decrease.11 Release the foot switch.12 While the joystick is activated, set the ramprate. Momentarily move the drive enabletoggle switch in the right direction to increasethe time or momentarily move the drive enabletoggle switch in the left direction to decreasethe time.Note: Each time the drive enable toggle switch ismomentarily moved, the time will change in 10%increments.13 Repeat steps 9 through 11 for each joystickcontrolled machine function.
|
