Contents - October
- safety rules
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Specifications
- Performance Specifications
- Hydraulic Component Specifications
- Manifold Component Specifications
- Machine Torque Specifications
- Hydraulic Hose and Fitting Torque Specifications
- Torque Procedure
- Section 3 Repair Procedures
- repair procedures
- Platform Controls
- Joysticks
- How to Adjust the Joystick Max-out Setting
- How to Adjust the Joystick Ramp Rate Setting
- How to Adjust the Joystick Threshold Setting
- How to Calibrate the Boom Angle Sensor
- Platform Components
- Platform Leveling Slave Cylinder
- Platform Rotator
- How to Bleed the Platform Rotator
- Platform Overload System
- Jib Boom Components
- Jib Boom Lift Cylinder
- Boom Components
- How to Repair the Cable Track
- How to Remove the Boom
- Boom Lift Cylinder
- Boom Extension Cylinder
- Boom Extend/Retract Cables
- How to Replace the Boom Extend/Retract Cables
- Platform Leveling Master Cylinder
- Engines
- How to Install the Flex Plate
- How to install the Pump and Bell Housing Assembly
- Ground Controls
- Hydraulic Pumps
- Drive Pump
- How to Prime the Pump
- Valve Adjustments - Function Manifold
- How to Adjust the Boom Extend Relief Valve
- Brake/Two-Speed Manifold Components
- Turntable Rotation Manifold Components
- Platform Rotate Manifold Components
- Platform Manifold Components, S-80
- Platform Manifold Components, S-85
- WD Traction Manifold Components
- Drive Oil Diverter Manifold Components (welder option)
- Valve Adjustments - Traction Manifold
- Valve Coils
- Fuel and Hydraulic Tanks
- Hydraulic Tank
- How to Remove the Turntable Rotation Hydraulic Motor
- How to Adjust the Turntable Rotation Gear Backlash
- turntable rotation components
- Steer Axle Components
- Drive Motors
- Steer Cylinders
- Non-steer Axle Components
- Oscillating Axle Components
- Oscillate Directional Valve
- How to Set Up the Directional Valve Linkage
- Section 4 Fault Codes
- Control System Fault Codes
- Fault Code Display - Deutz and Perkins Models
- F-22 Models
- Main Menu Structure - Deutz D 2.9 L4 Models
- Main Menu Structure - Perkins 404F-22 Models
- Deutz D 2.9 L4 Engine Fault Codes
- Perkins 404F-22 Engine Fault Codes
- Continental TME27 Engine Fault Codes
- Section 5 Schematics
- Electrical Symbol Legend
- Hydraulic Symbols Legend
- Relay and Fuse Panel Legend - Deutz TD2011L04i
- Relay and Fuse Panel Legend - Perkins 804D-33
- Connector Pin Legends
- Continental TME27 Engine Harness
- S-80X Ground Control Box Wiring Diagram
- Deutz TD2.9 L4 Engine Harness
- Perkins 404F-22T Engine Harness
- Electrical Schematic, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2.9 L4 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Ground Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Platform Control Box, S-80X - Deutz TD2011L04i Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 404F-22T Models (ANSI / CSA)
- Electrical Schematic, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Ground Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Platform Control Box, S-80X - Perkins 804D-33 Models (ANSI / CSA)
- Electrical Schematic, S-80X - Continental TME27 Models (ANSI / CSA)
- Ground Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Platform Control Box, S-80X - Continental TME27 Models (ANSI / CSA)
- Electrical Schematic, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2.9 L4 Models (CE)
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (CE)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (CE)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (CE)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (CE)
- Electrical Schematic, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Ground Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Platform Control Box, S-80 • S-85 - Deutz TD2011L04i Models (AS)
- Electrical Schematic, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Ground Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Platform Control Box, S-80 • S-85 - Perkins 804D-33 Models (AS)
- Electrical Schematic, S-80 • S-85 - Continental TME27 Models (AS)
- Ground Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Platform Control Box, S-80 • S-85 - Continental TME27 Models (AS)
- Continental Options Schematic
- Deutz and Perkins Options Schematic
- Platform Level Cutout, CTE Option
- kW Hydraulic Generator Wiring Diagram
- kW Hydraulic Generator Electrical Schematic
- Belt Driven Generator Option
- Hydraulic Schematics
- Hydraulic Schematic, 2WD Models
- Hydraulic Schematic, 4WD Models
|
Service and Repair Manual October 2016Steer Axle Components82 S-80 • S-85 • S-80X Part No. 126907411-1Yoke and Drive HubHow to Remove the Yoke andDrive Hub AssemblyNote: When removing a hose assembly or fitting,the O-ring (if equipped) on the fitting and/or hoseend must be replaced. All connections must betorqued to specification during installation. Refer toSpecifications, Hydraulic Hose and Fitting TorqueSpecifications.1 Remove the pin retaining fasteners from boththe steer cylinder and the tie rod cylinder pivotpins. Remove the pins.2 Tag, disconnect and plug the hydraulic hosesfrom the drive motor. Cap the fittings on thedrive motor.Bodily injury hazard. Sprayinghydraulic oil can penetrate andburn skin. Loosen hydraulicconnections very slowly to allowthe oil pressure to dissipategradually. Do not allow oil tosquirt or spray.3 Loosen the wheel lug nuts. Do not removethem.4 Block the non-steer wheels, and center a liftingjack of ample capacity under the steer axle.5 Raise the machine approximately 6 inches /15 cm and place blocks under the chassis forsupport.6 Remove the lug nuts. Remove the tire andwheel assembly.7 Remove the hydraulic hose clamp retainingfastener from the top of the yoke pivot pin.8 Remove the drive motor mounting fasteners.9 Slide the drive motor shaft out of the drive huband remove the drive motor from the machine.10 Remove the pin retaining fasteners from theupper and lower yoke pivot pins.11 Support and secure the yoke and drive hubassembly to a lifting jack.12 Use a slide hammer to remove the upper yokepivot pin. Use a soft metal drift to drive thelower yoke pivot pin down and out.Crushing hazard. The yoke anddrive hub assembly couldbecome unbalanced and fallwhen the yoke pivot pins areremoved if not properlysupported and secured to thelifting jack.13 Place the yoke and drive hub assembly on aflat surface with the drive hub facing down.14 Remove the drive hub mounting fasteners thatattach the drive hub to the yoke. Remove theyoke from the drive hub. Refer toSpecifications, Machine TorqueSpecifications.Note: Replace the thrust washer when installing theyoke and drive hub assembly onto the axle.
|
