1118. Identify the High Cable (31), which is theshorter of the two remaining cables. Route theeyelet end of the Cable up through the indicatedhole in the Top Frame (8).Wrap the High Cable (31) around a 90mm Pulley(24). Attach the Pulley inside of the Top Frame (8)with an M10 x 65mm Bolt (54), two 15mm x13mm Spacers (39), two M10 Washers (52), andan M10 Nylon Locknut (49).20. Remove the 90mm Pulleys (24) from the pre-assembled Pulley Plates (28).Wrap the High Cable (31) under a 90mm Pulley(24). Attach the Pulley and a Cable Trap (26) tothe second hole from the top of the two PulleyPlates (28) with an M10 x 45mm Bolt (57) and anM10 Nylon Locknut (49).21. Route the High Cable (31) up through the indicat-ed hole in the Top Frame (8).Wrap the High Cable (31) around a 90mm Pulley(24). Attach the Pulley, a Cable Trap (26), a15mm x 8mm Spacer (55), and a 15mm x 10mmSpacer (40) to the Top Frame (8) with an M10 x68mm Bolt (46), the two attached Support Plates(14), and an M10 Nylon Locknut (49). Do notovertighten the Bolt; the pulley must be ableto pivot easily.19. Route the High Cable (31) down through the indi-cated hole in the Top Frame (8).Wrap the High Cable (31) around a 90mm Pulley(24). Attach the Pulley and a Cable Trap (26)inside of the Top Frame (8) with an M10 x 65mmBolt (54), a 15mm x 13mm Spacer (39), a 15mmx 10mm Spacer (40), two M10 Washers (52), andan M10 Nylon Locknut (49).1819204921 552449 4614626 314057242628283140 3952525449 26 24831543939 52 85249 243181429. Press two 51mm x 76mm Outer Caps (79) ontothe Stabiliser (62). Attach the Stabiliser to theBench Frame (63) with two M10 x 60mmCarriage Bolts (50) and two M10 Nylon Locknuts(49).30. Press three 50mm Square Inner Caps (43) intothe Front Leg (64).Attach the Front Leg (64) to the Bench Frame(63) with two M10 x 65mm Bolts (54), two M10Washers (52), and two M10 Nylon Locknuts (49).Bench Assembly 2930434369828259 59598278LubricateAdjustmentTubesHole5252 6867 497463676856 5656645452 634949433132634962797950WideEnd31. Orient the Right and Left Backrest Frames (67,68) as shown. Press six 25mm x 50mm InnerCaps (82) into the Backrest Frames.Orient the Bench Backrest (69) with the wide endon the side shown. Attach the Backrest to theBackrest Frames (67, 68) with four M6 x 63mmBolts (56) and four M6 Washers (59). Do nottighten the Bolts yet.32. Lubricate the M10 x 180mm Bolt (78) withgrease. Attach the Backrest Frames (67, 68) tothe Bench Frame (63) with the Bolt, two M10Washers (52), and an M10 Nylon Locknut (49).Insert the Bench Pin (74) through a set of holes inthe adjustment tubes on the Backrest Frames(67, 68) and the indicated hole in the BenchFrame (63).Tighten the M6 x 63mm Bolts (56) used in step31.