Icar RPC 8BGA Complete Manual

Also see for RPC 8BGA: Quick guide Instruction manual Operating manual Resetting guide

Contents

Icar RPC 8BGA Complete Manual Manual pdf 38 page image

ICAR PQS rev8 may1838 / 86Set-up: editing pageWhen the editing screen is displayed, the parameter setting can be modified with ◄ and ►keys. The screen shows the newsetting, a graphic bar that shows the setting range, the maximum and minimum values, the previous setting and the factory default.Pressing ◄ + ▼the value decreases faster, while with ▲+ ►the value grows faster.Pressing simultaneously ◄ + ►, the setting is set to factory default. During the entry of a text string, keys ▲and ▼are used toselect the alphanumeric character while◄ and ► are used to move the cursor along the text string. Pressing keys ▲and▼simultaneously will move the character selection straight to character ‘A’. Press  to go back to the parameter selection. Theentered value is stored.Press ◄ to save all the settings and to quit the setup menu. The controller executes a reset and returns to normal operation.If the user does not press any key for more than 2 minutes, the system leaves the setup automatically and goes back to normalviewing without saving the changes done on parameters.N.B.: a backup copy of the setup data (settings that can be modified using the keyboard) can be saved in the eeprom memory ofthe power factor controller. This data can be restored when necessary in the work memory. The data backup 'copy' and 'restore'commands can be found in the commands menu. (see chapter 27. Command menu)20 PARAMETER TABLEBelow are listed all the programming parameters in tabular form. For each parameter are indicated the possible setting range andfactory default, as well as a brief explanation of the function of the parameter. The description of the parameter shown on thedisplay can in some cases be different from what is reported in the table because of the reduced number of characters available.The parameter code can be used however as a reference.Note: The parameters shown in the table with a shaded background are essential to the operation of the system, thus theyrepresent the minimum programming required for operation.M01 - UTILITY Psw (M15) UoM Default RangeP01.01 Language Usr EnglishEnglish / Italian / FrenchSpanish / PortugueseGerman / Polish / CzechRussian / CustomP01.02 Set clock at system power on Usr OFF OFF-ONP01.03 LCD contrast Usr % 50 0-100P01.04 Display backlit high intensity Usr % 100 0-100P01.05 Display backlit low intensity Usr % 25 0-50P01.06 Time to switch to low backlighting Usr s 180 5-600P01.07 Return to default page Usr s 60 OFF / 10-600P01.08 Default page Usr main (page list)P01.09 Plant description Usr (empty) String 20 chr.P01.01 – Select display text language.P01.02 – Active automatic clock settings access after power-up.P01.03 – Adjust LCD contrast.P01.04 – Display backlight high adjustment.P01.05 – Display backlight low adjustment.P01.06 – Display backlight low delay.P01.07 – Default page display restore delay when no key pressed. If set to OFF the display will always show the last page selected manually.P01.08 – Default page displayed on power-up and after delay.P01.09 – Free text with alphanumeric identifier name of specific panel/plant. If a description is set here, it will be shown as title of the home page. The samedescription will be used also for identification after remote reporting alarms/events via SMS/E-mail.M02 – GENERAL Psw (M15) UoM Default RangeP02.01 CT primary Usr A OFF OFF/1-30000P02.02 CT secondary Usr A 5 15P02.03 Plant type Usr Three-ph Three-phaseSingle phaseP02.04 Current reading phase Usr L1L1L2L3L1 L2 L3P02.05 CT polarity Usr AutAutDirRevP02.06 Voltage reading phase Usr L1-L2-L3L1-L2 / L2-L3 / L3-L1L1-N / L2-N / L3-N / L1-L2-L3L1-L2-L3-NSelected parameterMinimum possible settingGraph bar of the value-rangeNew value enteredMaximum possible settingFactory default setting