26|KDC-610UEnglish|279. Listen to the tuner9-1. Listening to the radioSelecting a tuner source1Press [SRC].Enters the Source selection mode.2Select a Tuner (“TUNER”) source using[Control] knob.Refer to Selecting a band (FM or AM)Press [R].Selecting a stationPress [E] or [F].The seek mode can be changed. Refer to (refer to below), <9-5.Tuner setting> (page 27).Selecting a Seek modePress [S].DisplayOperation“Auto1”Automatic search for a station.“Auto2”Search in order of the stations in the preset memory.“Manual”Normal manual tuning.9-2. Station preset memoryYou can store a station in the memory.1Press [E] or [F] to select the station.2Press [1/6].Enter the Preset mode.3Turn [Control] knob to select a memorynumber (FM: “1” – “18”, AM: “1” – “6”).4Press and hold [Control] knob.Exiting from the Preset memory modePress and hold [1/6].About the Mix Station preset mode•If you press [1/6] twice in step 2, the Mix Station presetmode is selected with “Mixed Preset List” displayed.In this mode, different bands and tuner sources (FM, AM,SiriusXM etc.) can be saved in the same preset layer, whichallows you to recall the desired station without switchingbetween bands or tuner sources.A maximum of six stations can be preset in the Mix Stationpreset mode.Once the Mix Station preset mode is set, you can enter thesame mode by just pressing [1/6] once in step 2.Pressing [1/6] twice allows you to return to the normalStation preset mode.9-3. Auto memoryYou can register 18 (FM)/ 6 (AM) stations with goodreception automatically.1Press [SRC] and select a Tuner (“TUNER”)source using [Control] knob.Refer to 2Press [R] to select a band.3Press [Control] knob.Enters the Function setting mode.4Select “Settings” > “Auto Memory” using[Control] knob.For how to use [Control] knob, refer to <3-3. Howto select the item> (page 9).5Select “YES” using [Control] knob.When 18 (FM)/ 6 (AM) stations that can be receivedare stored in the memory, the process in this modeis completed.Exiting from the Function setting modePress and hold [1/6].9-4. Recall preset stationRecall the stations in the memory.1Press [R] to select a band.2Press [1/6].Enter the Preset mode.3Select a memory number (FM: “1” – “18”, AM:“1” – “6”) using [Control] knob.9-5. Tuner settingYou can set up the tuner.1Press [SRC] and select a Tuner (“TUNER”)source using [Control] knob.Refer to 2Press [Control] knob.Enters the Function setting mode.3Select “Settings” using [Control] knob.For how to use [Control] knob, refer to <3-3. Howto select the item> (page 9).4Select a Tuner setting item using [Control]knob.DisplayDescription“Seek Mode”Sets the seek mode.“Auto1”: Automatic search for a station.“Auto2”: Search in order of the stations in the presetmemory.“Manual”: Normal manual tuning.“MONO”You can reduce the noise when stereo broadcasts arereceived as monaural.“ON”/ “OFF”“TI”Switches to the traffic information automatically whenthe traffic bulletin starts.“ON”/ “OFF”(Colored text: Factory setting)5Select a setting using [Control] knob.Returns to the previous item.Exiting from the Function setting modePress and hold [1/6].9-6. Direct access tuning(Function of remote control)You can search for a station directly by enteringfrequency.1Press [DIRECT] on the remote control.“– – – –” appears and enter the Direct access tuningmode.2Press the number buttons on the remotecontrol to enter the frequency.Example:Desired frequencyPress the following buttons92.1 MHz (FM)[9], [2], [1]810 kHz (AM)[8], [1], [0]3Press [ENT] on the remote control.Exiting from the Direct access tuning modePress [6] on the remote control.