Kenwood KDC-610U Instruction Manual

Also see for KDC-610U: Quick start guide

Contents

36 | KDC-610U English | 3712-5. Preset tuningRecalling a channel from the memory.1 Press [1/6] twice.Enter the Preset memory mode.2 Select a memory number (“1” – “24”) using[Control] knob.Enter the Preset memory mode.Exiting from the Preset memory modePress and hold [1/6].12-6. Tune Start™When tuning stations using the first 1-6 presets,songs will play from the beginning of each track ifTune Start is enabled.Refer to “Tune Start” of <12-20. SiriusXM tunersetting> (page 41).Note• Tune Start may take a few minutes to operate after a powercycle.12-7. Direct access tuning(Function of remote control)You can search for a channel directly by entering itsnumber.1 Press [DIRECT] on the remote control.2 Press the number buttons on the remotecontrol to enter the frequency.3 Press [ENT] on the remote control.Exiting from the Direct access tuning modePress [6] on the remote control.Automatic cancellation• If you operate no button for 10 seconds, the Direct AccessTuning mode is automatically canceled.12-3. Category and channel searchYou can select the channel and category you wantto receive.1 Press [1/6].“Category Search” appears and enter the Categoryand Channel search mode.2 Select a category using [Control] knob.For how to use [Control] knob, refer to <3-3. Howto select the item> (page 9).3 Select a channel using [Control] knob.Exiting the Category and Channel search modePress and hold [1/6].Until channel selection is enabled• You cannot search for a channel until the categoryinformation is acquired.12-4. Channel preset memoryYou can store a channel in the memory.1 Press [E] or [F] to select the channel.2 Press [1/6] twice.Enter the Preset memory mode.3 Turn [Control] knob to select a memorynumber (“1” – “24”).4 Press and hold [Control] knob.Exiting from the Preset memory modePress and hold [1/6].About the Mix Station preset mode• If you press [1/6] three times in step 2, the Mix Stationpreset mode is selected with “Mixed Preset List” displayed.In this mode, different bands and tuner sources (FM, AM,SiriusXM tuner etc.) can be saved in the same preset layer,which allows you to recall the desired station withoutswitching between bands or tuner sources.A maximum of six stations can be preset in the Mix Stationpreset mode.•12. SiriusXM™ Satellite Radio (optional tuner and service required)12-8. iTunes taggingYou can store the tag of the information about thesong being received, and send it to the connectediPod. You can easily find the song on the iTunesStore according to the tag sent to the iPod.1 Press and hold [R].“TAG” will be indicated on the display when songinformation can be registered.“TAG Storing” is indicated on the display while a tagis being stored in this unit. “TAG Stored” is indicatedon the display after a tag is stored.When your iPod is connected to this unit, “TAGTransferred” is shown on the display and a tag issent to the iPod.Effective use of iTunes• The song corresponding to the tag sent to the iPod isindicated in the playlist (“Tagged”) of the synchronizediTunes.By clicking your desired song in the playlist, you can easilyfind it on the iTunes Store and buy it from the iTunes Store.While ”TAG Storing” is displayed• Do not switch the source or remove the iPod while ”TAGStoring” is indicated.TAG will not be saved and cause a communication error inthis unit.Number of tags that can be stored• The memory usage can be checked by selecting the “TAGMemory” setting mentioned in <12-20. SiriusXM tunersetting> (page 41).Preparation for iTunes tagging• Select “ON” for “Tagging” as mentioned in <12-20. SiriusXMtuner setting> (page 41) when using this function.12-9. Parental Lock settingYou can turn on/off Parental Lock for each channel.1 Press [SRC] and select a SiriusXM (“SiriusXM”)source using [Control] knob.Refer to (page 10).2 Press [Control] knob.Enters the Function setting mode.3 Select “Settings” > “Parental Lock” using[Control] knob.For how to use [Control] knob, refer to <3-3. Howto select the item> (page 9).4 Enter the pass code.Operation type OperationSelection of numbers. Turn [Control] knob.Determination of the selected numbers. Press [Control] knob.Selection of column Press [E] or [F].Deletion of all numbers Press and hold [E].5 Select “Lock CH Edit” using [Control] knob.A category list is displayed.6 Select the category of the channel subjectusing [Control] knob.The list of the channels in the selected category isdisplayed.7 Select a channel using [Control] knob.Parental Lock for the selected channel is turned onand off alternately each time you press [Control]knob.“ ” is indicated for the selected channel.Exiting from the Function setting modePress and hold [1/6].Pass code setting• The pass code is set to “0000” as default.For how to change the pass code, refer to <12-12. ParentalLock pass code setting> (page 39).When the “Lock CH Edit” item is not displayed• The mature content setting may be turned ON. Refer to<12-11. Setting Parental Lock for Mature content> (page38).Listening to the channel for which Parental Lock is turnedon• If a channel for which Parental Lock is turned on is selected,a pass code input screen appears. Programs on the selectedchannel can be received only when the input pass code iscorrect.