Kenwood KDC-X7000DAB Instruction Manual

Also see for KDC-X7000DAB: Instruction manual

Contents

ENGLISH 19AUDIO SETTINGSBASS BOOST LEVEL1/ LEVEL2/ LEVEL3/ LEVEL4/ LEVEL5: Selects your preferredbass boost level. ; OFF: Cancels.LOUDNESS LEVEL1/ LEVEL2: Selects your preferred low and high frequenciesboost to produce a well-balanced sound at a low volume level. ;OFF: Cancels.SUBWOOFER SET ON: Turns on the subwoofer output. ; OFF: Cancels.FADER (Not applicable if 3-way crossover is selected.)R15 to F15 (0): Adjusts the rear and front speaker output balance.BALANCE L15 to R15 (0): Adjusts the left and right speaker output balance.VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source. (Beforeadjustment, select the source you want to adjust.)SOUND EFFECTSOUND RECNSTR(Soundreconstruction)(Not applicable for TUNER source, DIGITAL AUDIO source and AUXsource.)ON: Creates realistic sound by compensating the high-frequencycomponents and restoring the rise-time of the waveform that are lostin audio data compression. ; OFF: Cancels.SPACE ENHANCE (Not applicable for TUNER source and DIGITAL AUDIO source.)SMALL/ MEDIUM/ LARGE: Virtually enhances the sound space. ;OFF: Cancels.SND REALIZER LEVEL1/ LEVEL2/ LEVEL3: Virtually makes the sound more realistic. ;OFF: Cancels.STAGE EQ LOW/ MIDDLE/ HIGH: Virtually adjust the sound position heard fromthe speakers. ; OFF: Cancels.DRIVE EQ ON: Boosts the frequency to reduce the noise heard from outside thecar or running noise of the tyres. ; OFF: Cancels.SPEAKER SIZE Depending on the crossover type you have selected ( 5), 2-waycrossover or 3-way crossover setting items will be shown. ( 20)By default, 2-way crossover type is selected.X ‘ OVER[SUB-W LEVEL] is selectable only if [SUBWOOFER SET] is set to [ON].Crossover settingsBelow are the available setting items for 2-way crossover and 3-waycrossover.SPEAKER SIZESelects according to the connected speaker size for optimumperformance.• The frequency and slope settings are automatically set for thecrossover of the selected speaker.• If [NONE] is selected for [TWEETER] of [FRONT], [REAR] and [SUBWOOFER] for[SPEAKER SIZE], the [X ‘ OVER] setting of the speaker is not available.X ‘ OVER[FRQ]/ [F - HPF FRQ]/ [R - HPF FRQ]/ [SW LPF FRQ]/ [HPF FRQ]/ [LPF FRQ]:Adjusts the crossover frequency for the selected speakers (high passfilter or low pass filter).• If [THROUGH] is selected, all signals are sent to the selected speakers.[F - HPF SLOPE]/ [R - HPF SLOPE]/ [SW LPF SLOPE]/ [HPF SLOPE]/ [LPF SLOPE]/[SLOPE]:Adjusts the crossover slope.• Selectable only if a setting other than [THROUGH] is selected for thecrossover frequency.[SW LPF PHASE]/ [PHASE]:Selects the phase of the speaker output to be in line with the otherspeaker output.[GAIN LEFT]/ [GAIN RIGHT]/ [F - HPF GAIN]/ [R - HPF GAIN]/ [SW LPF GAIN]/ [GAIN]:Adjusts the output volume of the selected speaker.The following items is selectable only if [SUBWOOFER SET] is set to [ON]:– [SUBWOOFER]/ [WOOFER] of [SPEAKER SIZE]– [SUBWOOFER LPF]/ [WOOFER] of [X ‘ OVER]