(No.RA015)1-519. P25H-CPMDevia-tion1) Adj item:[P2 P2DEV]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]*F5,F6,K5,K6type only: Pressand hold the[Right] key to en-ter [Center1](Over LapHigh)→Adjust:[****]PTT : ONPress [ ] key tostore the adjust-ment value.1) Adj item:[P25 H-CPM Devia-tion]Deviation meterLPF: 3kHzHPF: OFF2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]*F5,F6,K5,K6 typeonly: [Center1](Over Lap High)→Press [Transmit]button.Press [Apply All]button to store theadjustment value.Devia-tionmeterOscil-lo-scopePanel ANT Panel [Paneltuningmode][],[][PCtestmode][←],[→]Write fixed value “498”(F2,F3,K2,K3),“497”(F5,F6,K5,K6) for eachadjustment point. Trans-mit at each adjustmentpoint and check that thedeviation is between3090Hz and 3215Hz.Deviation meterLPF: 3kHzHPF: OFF[Panel tuning mode]PTT: ON[PC test mode]PTT: Press [Transmit]button3090~3215Hz[PC testmode]Press [ApplyAll] button tostore theadjustmentvalue after alladjustmentpoints havebeen adjust-ed.10.NXDNHighDevia-tion[NXDNNarrow]1) Adj item:[Nn NDEV]Adjust:[****]Deviation meterLPF: 3kHzHPF: OFF2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]*F5,F6,K5,K6type only: Pressand hold the[Right] key to en-ter [Center1](Over LapHigh)→Adjust:[****]PTT : ONPress [ ] key tostore the adjust-ment value.1) Adj item:[NXDN High Devia-tion (NXDN Narrow]Deviation meterLPF: 3kHzHPF: OFF2) Adj item:[Low1]→[Low3]→[Low5]→[Center1]→[Center3]→[Center5]→[High2]→[High4]→[High6]*F5,F6,K5,K6 typeonly: [Center1](Over Lap High)→Press [Transmit]button.Press [Apply All]button to store theadjustment value.Devia-tionmeterOscil-lo-scopePanel ANT Panel [Paneltuningmode][],[][PCtestmode][←],[→]Write fixed value “497”for each adjustmentpoint. Transmit at eachadjustment point andcheck that the deviationis between 2995Hz and3117Hz.Deviation meterLPF: 3kHzHPF: OFF[Panel tuning mode]PTT: ON[PC test mode]PTT: Press [Transmit]button2995~3117Hz[PC testmode]Press [ApplyAll] button tostore theadjustmentvalue after alladjustmentpoints havebeen adjust-ed.Item Condition Measurement Adjustment Specifica-tions/RemarksPanel tuningmodePC test mode Test-equip-mentUnit Ter-minalUnit Parts Method