TK-7360/7360H/7360H ( V )55-2. Connection procedure1. Connect the transceiver to the computer using the inter-face cable and USB adapter (When the interface cable isKPG-46A, the KCT-53U can be used.).Note:• You must install the KCT-53U driver in the computer touse the USB adapter (KCT-53U).• When using the USB adapter (KCT-53U) for the first time,plug the KCT-53U into a USB port on the computer withthe computer power ON.2. When the Power is switched on, user mode can be en-tered immediately. When the PC sends a command, thetransceiver enters PC mode, and “PROGRAM” is dis-played on the LCD.When data is transmitting from the transceiver, the redLED blinks.When data is receiving by the transceiver, the green LEDblinks.Note:The data stored in the computer must match the “ModelName” when it is written into the EEPROM.5-3. KPG-46/KPG-46A description(PC programming interface cable: Option)The KPG-46/46A is required to interface the transceiverto the computer. It has a circuit in its D-sub connector (KPG-46: 25-pin, KPG-46A: 9-pin) case that converts the RS-232Clogic level to the TTL level.The KPG-46/46A connects the 8-pin microphone connec-tor of the transceiver to the RS-232C serial port of the com-puter.5-4. KCT-53U description (USB adapter: Option)The KCT-53U is a cable which connects the KPG-46A toa USB port on a computer.When using the KCT-53U, install the supplied CD-ROM(with driver software) in the computer. The KCT-53U driverruns under Windows 2000, XP or Vista (32-bit).5-5. FPU (Programming Software) descriptionThe FPU is the programming software for the transceiversupplied on a CD-ROM. This software runs under WindowsXP, Vista or 7 on a PC.The data can be input to or read from the transceiver andedited on the screen. The programmed or edited data canbe printed out. It is also possible to tune the transceiver.List of FPU for transceiverModel Type FPUTK-7360 M,M2 KPG-135D(M)TK-7360H K KPG-135D(K)TK-7360H M KPG-135D(M)TK-7360H(V) K KPG-135D(K)FPUPCKPG-46 or KPG-46A orKPG-46A + KCT-53U +Tuning cable(E30-3383-05)KPG-46TransceiverPCD-SUB(25-pin)TransceiverPCKPG-46AD-SUB(9-pin)TransceiverPCKPG-46AKCT-53UUSBFig. 16. Clone ModeProgramming data can be transferred from one trans-ceiver to another by connecting them via their modularmicrophone jacks. The operation is as follows (the transmittransceiver is the source and the receive transceiver is a tar-get).Note :Clone mode should be enabled.1. Turn the source transceiver power ON with the [ ] keyheld down (1 second), “CLONE MODE” is displayed onthe LCD.2. Power on the target transceiver.3. Connect the cloning cable (No. E30-3382-05) to the mod-ular microphone jacks on the source and target.4. Press the [ ] key on the source transceiver.The data of the source is sent to the target. While thesource is sending data, red LED blinked. While the tar-get is receiving the data, “PROGRAM” is displayed andgreen LED blinked. When cloning of data is completed,the source displays “END”, and the source red LEDturned off, and the target automatically operates in theUser mode. The target can then be operated by thesame program as the source.5. The other target can be continuously cloned. Carry outthe operation in step 2 to 4.REALIGNMENT