Kenwood VR-716 Instruction Manual

Also see for VR-716: Service manual Instruction manual

16 EN4¢ + ++MULTI CONTROLSETUPSetupPOWER RCVRPOWERON/STANDBYMulti % / fiPreparing for surround soundSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.It is not advisable to select “LRG” (large) for front, center, and surroundspeakers as this will cause the speakers to malfunction.1Turn on the power to this receiver by pressing POWER ON/STANDBY or POWER RCVR key.2For the remote control, press and hold the TUNER key for morethan 3 seconds to switch to receiver mode.3Press the SETUP key to enter the SETUP mode and use theMULTI CONTROL knob or Multi %/ fikeys for the followingdisplays.1 SP SETUP2 TESTTONE3 DISTANCE4 EXITThe flow of the SETUP is as follows;SP SETUP TESTTONE DISTANCE EXITFrontCenterSurroundSP SystemLCRSRSLSWLCRSRSLSWMANUALAUTOFull Range2Way 2Speaker2Way 3SpeakerOthersSubwooferFrontCenterSurroundSubwoofer Re-mix4Select a speaker system.1 Select SP SETUP and press the SETUP key again so that thespeaker system indication “SP SYSTEM” scrolls across thedisplay.2 Use the MULTI CONTROL knob or Multi % / fi keys to select thespeaker system setting.1 FULL RANGE : For selected Kenwood speaker – for example,KS-207HT.2 2WAY 2SPKR : For selected Kenwood speaker – for example,KS-307HT.3 2WAY 3SPKR : For selected Kenwood speaker – for example,KS-707HT.4 OTHERS : For general speakers.• The selection of FULL RANGE, 2WAY 2SPKR or 2WAY 3SPKRshould only be used with 5 channels speaker system setting.• When the setting FULL RANGE, 2WAY 2SPKR or 2WAY 3SPKRis selected, the procedure skips to step 5.3 For general speaker setting, use the MULTI CONTROL knob orMulti % / fi keys to select OTHERS and press the SETUP keyagain.• The subwoofer setting indication “SUBW ON” appears.4 Use the MULTI CONTROL knob or Multi % / fi keys to selectthe appropriate subwoofer setting.1 SUBW ON : Subwoofer setting mode to the receiver is ON.2 SUBW OFF : Subwoofer setting mode to the receiver is OFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakersare automatically set to “FRNT LRG” and the procedure skips tostep 7.Before step 7, press the SETUP key to accept the setting.• When subwoofer output sound is required, select “FRNT NML”.5 Press the SETUP key to accept the setting.• The front speakers setting indication “FRNT NML” appears.6 Use the MULTI CONTROL knob or Multi % / fi keys to selectthe appropriate front speakers setting.1 FRNT NML (normal) : Average size front speakers areconnected to the receiver.2 FRNT LRG (large) : Large front speakers are connected tothe receiver.• You are advised to select “NML” (normal) for front speakers.• For “FRNT LRG” selection, no sound will be heard from subwooferspeaker even when it is set to ON. However, if you select “SWRE-MIX ON” when subwoofer is selected, you will be able tohear sound from the subwoofer.When in STEREO mode, the sound goes directly to front speaker.7 Press the SETUP key to accept the setting.• The center speaker setting indication “CNTR NML” appears.8 Use the MULTI CONTROL knob or Multi % / fi keys to selectthe appropriate center speaker setting.If you have selected “LRG” as the front speakers setting,1 CNTR NML (normal) : An average size center speaker isconnected to the receiver.2 CNTR LRG (large) : A large center speaker is connected tothe receiver.3 CNTR OFF : Center speaker setting mode to thereceiver is OFF.• You are advised to select “NML” (normal) for center speaker.If you have selected “NML” as the front speakers setting,1 CNTR ON : Center speaker setting mode to thereceiver is ON.2 CNTR OFF : Center speaker setting mode to thereceiver is OFF.