Kenwood VR-8070 Instruction Manual

Also see for VR-8070: Service manual

21 ENENGLISH5Adjust the speaker volume level.From your usual listening position, adjust the volume levels. Thevolume levels from each speaker should be the same.• The receiver enters the speaker volume level adjustment mode.• Indicators appear only for the channels of the speakers selectedin step 4.Be aware that the TEST TONE is quite a loud sound (0dB).1 Press the ∧∧∧∧∧/∨∨∨∨∨ keys or @/#keys to select TEST TONE.2 Press the SETUP key for the following displays:1 T.TONE AUTO2 T.TONE MANUAL3 The selection of AUTO/MANUAL TEST TONE is done by theMULTI CONTROL knob or Multi (%/fi) keys.Press the SETUP key again to begin TEST TONE.Use the MULTI CONTROL knob or Multi (%/fi) keys to adjustthe volume level of the test tone output from the speakerchannel to be adjusted.For AUTO selection, the first test tone is heard from the FrontLeft Speaker for 2.5 seconds. The next test tone is heard fromthe speakers in the following sequence for 2 seconds each.LEFT CNTR RIGHT SRSBL SBRSLSUBWThe channel indication blinks while the test tone is being output.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE• If you change the volume level settings for the speakers whilelistening to music, the settings referred to on this page are alsochanged. fi• If the speaker setting selects are OFF, the speaker level settingsare reset.For MANUAL selection, press the ∧∧∧∧∧/∨∨∨∨∨ keys or @/# keys eachtime to select the speaker channel.4 Press the SETUP key again.• The test tone is turned off and return to the main setup displays.6Adjust the bass peak level.A restriction is put on the low frequency so that the bass peak levelwill not go higher than the acceptable level when the volume isincreased.If Subwoofer is OFF, the limitation will affect the low frequency ofthe Front Left and Right Speakers.1 Press the ∧∧∧∧∧/∨∨∨∨∨ keys or @/ # keys to select BASS PEAK and pressthe SETUP key.SP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE2 Use the MULTI CONTROL knob or Multi (%/fi) keys to adjustthe bass peak level to –30dB.• The adjustment range is from – 30dB to 0dB and OFF.Preparing for surround sound8 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate Surround Speaker setting.If you selected “LARGE” as the Center Speaker setting,1 SURR NML/THX : Average size Surround Speakers areconnected to the receiver.2 SURR LARGE : Large Surround Speakers areconnected to the receiver.3 SURR OFF : Surround Speaker setting mode tothe receiver is OFF.If you selected other than “LARGE” as the Center Speakersetting,1 SURR NML/THX : Average size Surround Speakers areconnected to the receiver.2 SURR OFF : Surround Speaker setting mode tothe receiver is OFF.• When the setting “SURR OFF” is selected, you may skip to step!.9 Press the ∧∧∧∧∧ key or # key again to accept the setting.• The Surround Speaker setting indication “SB” appears.0 Use the MULTI CONTROL knob or Multi (%/fi) keys to selectappropriate Surround Back Speaker setting.If you selected “LARGE” as the Surround Speaker setting,1 SB NML/THX : Average size Surround Back Speaker isconnected to the receiver.2 SB LARGE : Large Surround Back Speaker is con-nected to the receiver.3 SB OFF : Surround Back Speaker setting mode tothe receiver is OFF.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFEIf you selected “NML/THX” as the Surround Speaker setting,1 SB NML/THX : Average size Surround Back Speaker isconnected to the receiver.2 SB OFF : Surround Back Speaker setting mode tothe receiver is OFF.! Press the ∧∧∧∧∧ key or # key again to accept the setting.• The Subwoofer re-mix setting indication “SW RE-MIX” ap-pears.@ Use the MULTI CONTROL knob or Multi (%/fi) keys to selectthe appropriate Subwoofer re-mix setting.1 SW RE-MIX ON : Subwoofer re-mix setting mode tothe receiver is ON.2 SW RE-MIX OFF : Subwoofer re-mix setting mode tothe receiver is OFF.• If subwoofer is turned off, subwoofer re-mix setting is not visible.# Press the SETUP key again to return to the main setupdisplays.7 Press the ∧∧∧∧∧ key or # key again to accept the setting.• The Surround Speaker indication “SURR” appears.Continued to next page.