Kenwood VR-8070 Instruction Manual

Also see for VR-8070: Service manual

39 ENBasic remote control operations for other componentsChecking the codesIf you have setup the remote control using the procedures described in“Searching for your codes”, you may need to find out which four-digitcode is operating your equipment:For example, to find out which code is operating your TV:1Press the TV key once. Next, press and hold the Remote Setupkey until the LED blinks twice, then release the Remote Setupkey.2Press the Numeric key to enter 9, 9, ).• The LED will blink twice.3To view the code for the first digit, press “1” once. Wait for 3seconds, counts the number of times the LED blinks (e.g.,blinks=3) and write down that number.• If a code digit is “0”, the LED will not blink.4Repeat step 3three more times for the remaining digits. Use“2” for the second digit, “3” for the third digit, and “4” for thefourth digit.5To check the codes of your other components, repeat steps1through 4, but substitute the appropriate key (i.e.,DVD/6CH, CD/DVD, VID1, VID2, VID3, TV, MD/TAPE, AV AUX,PHONO) for the component you are checking.• As suggested earlier on, write down each of the four-digit code.• PHONO key has to be re-assigned to another key before a setupcode can be programmed.Re-assigning device keysThe remote control can be setup to control second TV or VCR, or anycombination of eight home entertainment components.For example, to control the operation of two different VCR using theremote control, the user need to re-assign the unused VID2 key tooperate the second VCR(VID1) as follows:1Press and hold the Remote Setup key until the LED blinkstwice, then release the Remote Setup key.2Press the Numeric key to enter 9, 9, 2.• The LED will blink twice.3Press VID1 key once, then press the VID2 key once.• The user now can operate VID2 as a second VCR along with VID1.• Refer to the table in the previous page for the combination ofsource keys and the other components assignment. °4To re-assign other device keys, repeat steps 1through 3bysubstituting the key sequence from the below chart for themost popular components:5To clear the re-assignment and reset the remote control to itsoriginal operation mode:1 Press and hold the Remote Setup key until the LED blinkstwice, then release the remote setup key.2 Press the Numeric key to enter 9, 9, 2.3 Press VID2 key twice.• When a re-assignment is done, the LED will blink twice to confirmyour choice. At that time, you will need to program the remotecontrol in order to control the new component.• If an invalid key sequence is entered, the LED blink once and returnto normal operation.• When in Tuner mode, re-assignment is not available.Operating other componentsThis operation lets you operate the registered components.SRC PowerSourcekeys1Use the source keys to select the component you desire.• Pressing the source keys also changes the input selector on thereceiver.2Press the SRC Power key.• To return to the receiver operation mode, press the TUNER key formore than 3 seconds.3Press the operation keys you desire. rThe remote control mode remains at the selected input. If youwish to operate another component, repeat step 2 or 3.To re-assign keySequence PerformTV as 2nd VID1 key Remote Setup 9 9 2 VID1 TVTV as 2nd VID2 key Remote Setup 9 9 2 VID2 TVTV as 2nd CD/DVD key Remote Setup 9 9 2 CD/DVD TVTV as 2nd TV key Remote Setup 9 9 2 TV TVVID1 as 2nd TV key Remote Setup 9 9 2 TV VID1VID1 as 2nd VID2 key Remote Setup 9 9 2 VID2 VID1VID1 as 2nd CD/DVD key Remote Setup 9 9 2 CD/DVD VID1VID1 as 2nd VID1 key Remote Setup 9 9 2 VID1 VID1Resetting the Remote control• To initilize the remote control, press the Remote Setup key untilthe LED blinks twice. Then press the Numeric key to enter 9,8, 1. The LED will blink twice.