Makita DLS110 Instruction Manual

Also see for DLS110: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

17 ENGLISHOnly for EU countriesDo not dispose of electric equipmenttogether with household waste material! Inobservance of the European Directive, onWaste Electric and Electronic Equipmentand its implementation in accordance withnational law, electric equipment that havereached the end of their life must be col-lected separately and returned to an envi-ronmentally compatible recycling facility.Intended useThe tool is intended for accurate straight and mitercutting in wood. With appropriate saw blades, aluminumcan also be sawed.NoiseThe typical A-weighted noise level determined accord-ing to EN62841:Model DLS110Sound pressure level (LpA ) : 92 dB(A)Sound power level (LWA ) : 102 dB (A)Uncertainty (K) : 3 dB(A)Model DLS111Sound pressure level (LpA ) : 92 dB(A)Sound power level (LWA ) : 102 dB (A)Uncertainty (K) : 3 dB(A)Model DLS112Sound pressure level (LpA ) : 92 dB(A)Sound power level (LWA ) : 102 dB (A)Uncertainty (K) : 3 dB(A)WARNING: Wear ear protection.VibrationThe vibration total value (tri-axial vector sum) deter-mined according to EN62841:Model DLS110Vibration emission (a h) : 2.5 m/s2 or lessUncertainty (K) : 1.5 m/s2Model DLS111Vibration emission (a h) : 2.5 m/s2 or lessUncertainty (K) : 1.5 m/s2Model DLS112Vibration emission (a h) : 2.5 m/s2 or lessUncertainty (K) : 1.5 m/s2NOTE: The declared vibration emission value has beenmeasured in accordance with the standard test methodand may be used for comparing one tool with another.NOTE: The declared vibration emission value mayalso be used in a preliminary assessment of exposure.WARNING: The vibration emission during actualuse of the power tool can differ from the declaredemission value depending on the ways in which thetool is used.WARNING: Be sure to identify safety measuresto protect the operator that are based on an estima-tion of exposure in the actual conditions of use (takingaccount of all parts of the operating cycle such asthe times when the tool is switched off and when it isrunning idle in addition to the trigger time).EC Declaration of ConformityFor European countries onlyThe EC declaration of conformity is included as Annex Ato this instruction manual.SAFETY WARNINGSGeneral power tool safety warningsWARNING: Read all safety warnings, instruc-tions, illustrations and specifications providedwith this power tool. Failure to follow all instructionslisted below may result in electric shock, fire and/orserious injury.Save all warnings and instruc-tions for future reference.The term "power tool" in the warnings refers to yourmains-operated (corded) power tool or battery-operated(cordless) power tool.Safety instructions for mitre saws1. Mitre saws are intended to cut wood or wood-like products, they cannot be used with abra-sive cut-off wheels for cutting ferrous materialsuch as bars, rods, studs, etc. Abrasive dustcauses moving parts such as the lower guard tojam. Sparks from abrasive cutting will burn thelower guard, the kerf insert and other plastic parts.2. Use clamps to support the workpiece when-ever possible. If supporting the workpieceby hand, you must always keep your hand atleast 100 mm from either side of the saw blade.Do not use this saw to cut pieces that are toosmall to be securely clamped or held by hand.If your hand is placed too close to the saw blade,there is an increased risk of injury from bladecontact.3. The workpiece must be stationary andclamped or held against both the fence and thetable. Do not feed the workpiece into the bladeor cut "freehand" in any way. Unrestrainedor moving workpieces could be thrown at highspeeds, causing injury.4. Push the saw through the workpiece. Do notpull the saw through the workpiece. To makea cut, raise the saw head and pull it out overthe workpiece without cutting, start the motor,press the saw head down and push the sawthrough the workpiece. Cutting on the pull strokeis likely to cause the saw blade to climb on topof the workpiece and violently throw the bladeassembly towards the operator.5. Never cross your hand over the intended lineof cutting either in front or behind the sawblade. Supporting the workpiece "cross handed"i.e. holding the workpiece to the right of the sawblade with your left hand or vice versa is verydangerous.

/ 244

Related manuals for Makita DLS110

Makita DLS110 Instruction Manual

This manual is suitable for:

DLS110 DLS111 DLS112

manualsdatabase

Your AI-powered manual search engine