Makita DLS110 Instruction Manual

Also see for DLS110: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

31 ENGLISHWIRELESS ACTIVATIONFUNCTIONFor DLS111 onlyWhat you can do with the wirelessactivation functionThe wireless activation function enables clean and com-fortable operation. By connecting a supported vacuumcleaner to the tool, you can run the vacuum cleanerautomatically along with the switch operation of the tool.► Fig.58To use the wireless activation function, prepare follow-ing items:• A wireless unit• A vacuum cleaner which supports the wirelessactivation functionThe overview of the wireless activation function settingis as follows. Refer to each section for detail procedures.1. Installing the wireless unit2. Tool registration for the vacuum cleaner3. Starting the wireless activation functionInstalling the wireless unitCAUTION: Place the tool on a flat and stablesurface when installing the wireless unit.NOTICE: Clean the dust and dirt on the tool beforeinstalling the wireless unit. Dust or dirt may causemalfunction if it comes into the slot of the wireless unit.NOTICE: To prevent the malfunction caused bystatic, touch a static discharging material, suchas a metal part of the tool, before picking up thewireless unit.NOTICE: When installing the wireless unit, alwaysbe sure that the wireless unit is inserted in the cor-rect direction and the lid is completely closed.1. Open the lid on the tool as shown in the figure.► Fig.59: 1. Lid2. Insert the wireless unit to the slot and then closethe lid.When inserting the wireless unit, align the projectionswith the recessed portions on the slot.► Fig.60: 1. Wireless unit 2. Projection 3. Lid4. Recessed portionWhen removing the wireless unit, open the lid slowly.The hooks on the back of the lid will lift the wireless unitas you pull up the lid.► Fig.61: 1. Wireless unit 2. Hook 3. LidAfter removing the wireless unit, keep it in the suppliedcase or a static-free container.NOTICE: Always use the hooks on the back ofthe lid when removing the wireless unit. If thehooks do not catch the wireless unit, close the lidcompletely and open it slowly again.Tool registration for the vacuumcleanerNOTE: A Makita vacuum cleaner supporting thewireless activation function is required for the toolregistration.NOTE: Finish installing the wireless unit to the toolbefore starting the tool registration.NOTE: During the tool registration, do not pull theswitch trigger or turn on the power switch on thevacuum cleaner.NOTE: Refer to the instruction manual of the vacuumcleaner, too.If you wish to activate the vacuum cleaner along withthe switch operation of the tool, finish the tool registra-tion beforehand.1. Install the batteries to the vacuum cleaner and thetool.2. Set the stand-by switch on the vacuum cleaner to"AUTO".► Fig.62: 1. Stand-by switch3. Press the wireless activation button on the vac-uum cleaner for 3 seconds until the wireless activationlamp blinks in green. And then press the wireless acti-vation button on the tool in the same way.► Fig.63: 1. Wireless activation button 2. Wirelessactivation lampIf the vacuum cleaner and the tool are linked success-fully, the wireless activation lamps will light up in greenfor 2 seconds and start blinking in blue.NOTE: The wireless activation lamps finish blinkingin green after 20 seconds elapsed. Press the wirelessactivation button on the tool while the wireless acti-vation lamp on the cleaner is blinking. If the wirelessactivation lamp does not blink in green, push the wire-less activation button briefly and hold it down again.NOTE: When performing two or more tool registra-tions for one vacuum cleaner, finish the tool registra-tion one by one.Starting the wireless activationfunctionNOTE: Finish the tool registration for the vacuumcleaner prior to the wireless activation.NOTE: Refer to the instruction manual of the vacuumcleaner, too.After registering a tool to the vacuum cleaner, thevacuum cleaner will automatically runs along with theswitch operation of the tool.1. Install the wireless unit to the tool.2. Connect the hose of the vacuum cleaner with thetool.► Fig.643. Set the stand-by switch on the vacuum cleaner to"AUTO".► Fig.65: 1. Stand-by switch

/ 244

Related manuals for Makita DLS110

Makita DLS110 Instruction Manual

This manual is suitable for:

DLS110 DLS111 DLS112

manualsdatabase

Your AI-powered manual search engine