Makita DLS110 Instruction Manual

Also see for DLS110: Instruction manual Instruction manual Instruction manual Instruction manual Instruction manual

28 ENGLISHBevel cutWARNING: After setting the blade for a bevelcut, ensure that the carriage and blade will havefree travel throughout the entire range of theintended cut before operating the tool. Interruptionof the carriage or blade travel during the cutting oper-ation may result in kickback and serious personalinjury.WARNING: While making a bevel cut keephands out of the path of the blade. The angle of theblade may confuse the operator as to the actual bladepath while cutting and contact with the blade willresult in serious personal injuryWARNING: The blade should not be raiseduntil it has come to a complete stop. During abevel cut the piece cut off may come to rest againstthe blade. If the blade is raised while it is rotating thecut-off piece maybe ejected by the blade causingthe material to fragment which may result in seriouspersonal injury.NOTICE: When pressing down the handle, applypressure in parallel with the blade. If a force isapplied perpendicularly to the turn base or if the pres-sure direction is changed during a cut, the precisionof the cut will be impaired.► Fig.491. Remove the upper fence on the side that you aregoing to tilt the carriage.2. Unlock the stopper pin.3. Adjust the bevel angle according to the procedureexplained in the "Adjusting the bevel angle" section.Then tighten the knob.4. Secure the workpiece with a vise.5. Pull the carriage toward you fully.6. Switch on the tool without the blade making anycontact and wait until the blade attains full speed.7. Gently lower the handle to the fully lowered posi-tion while applying pressure in parallel with the bladeand push the carriage toward the guide fence to cutthe workpiece.8. When the cut is completed, switch off the tool andwait until the blade has come to a complete stopbefore returning the blade to its fully elevated position.Compound cuttingCompound cutting is the process in which a bevelangle is made at the same time in which a miter angleis being cut on a workpiece. Compound cutting can beperformed at the angle shown in the table.Miter angle Bevel angleLeft and Right 0° - 45° Left and Right 0° - 45°When performing compound cutting, refer to "Press cut-ting", "Slide (push) cutting", "Miter cutting" and "Bevelcut" explanationsCutting crown and cove moldingsCrown and cove moldings can be cut on a compoundmiter saw with the moldings laid flat on the turn base.There are two common types of crown moldings andone type of cove moldings; 52/38° wall angle crownmolding, 45° wall angle crown molding and 45° wallangle cove molding.► Fig.50: 1. 52/38° type crown molding 2. 45° typecrown molding 3. 45° type cove moldingThere are crown and cove molding joints which aremade to fit "Inside" 90° corners ((a) and (b) in the figure)and "Outside" 90° corners ((c) and (d) in the figure.)(a) (b) (c) (d)1 21. Inside corner 2. Outside corner2(a)(b)(a)(b)(b)(a)(b)(a)(a)(b)(c) (d)11. Inside corner 2. Outside cornerMeasuringMeasure the wall width, and adjust the width of theworkpiece according to it. Always make sure that widthof the workpiece's wall contact edge is the same as walllength.► Fig.51: 1. Workpiece 2. Wall width 3. Width of theworkpiece 4. Wall contact edgeAlways use several pieces for test cuts to check thesaw angles.When cutting crown and cove moldings, set the bevelangle and miter angle as indicated in the table (A) andposition the moldings on the top surface of the sawbase as indicated in the table (B).

/ 244

Related manuals for Makita DLS110

Makita DLS110 Instruction Manual

This manual is suitable for:

DLS110 DLS111 DLS112

manualsdatabase

Your AI-powered manual search engine