NAD T585 Owner's Manual

Also see for T 585: Catalog Owner's manual Specifications Service manual Technical bulletin

NAD T585 Owner's Manual Manual pdf 13 page image

brightneSS/contraSt/Saturation/SharpneSS/gammaPicture Setting adjustment is available for the following options.brightness: Adjust overall brightness of the image.contrast: Adjust bright areas (white level) in the image.Saturation: Adjust the dullness or richness of image color. A colorwith absolutely no saturation is going to be gray. A color that is 100%saturated is in its most intense form.Sharpness: Picture sharpness could be easily lost during therecording/playback process. Adjust sharpness to improve the finedetails of the picturegamma: Adjust intensity of the picture non-linearly. Select whenan image’s dark portions appears obscure or bright portions becomebrighter than necessary.NOTES• The level of adjustment for Brightness, Contrast, Saturation andSharpness (all defaulted to “0”) range from -4 to +4 while Gamma isfrom 0.761 up to 1.315.• Refer also to the item on PICTURE SETTING ADJUSTMENT at the VIDEOSETTING section of the REFERENCE page.video outputTurn ON/OFF either HDMI audio/video OUT or VGA OUT. HDMI OUT andVGA OUTPUT can only be turned ON one at a time – if HDMI is set to ON,VGA is automatically set to OFF and vice versa.Scart (europe model onlY)SCART carries both composite video and RGB signals. Select the videooutput signal that will be routed over SCART OUT.cvbS: Select to output composite video signals.rgb: Split the signal into the three fundamental colors Red, Green andBlue (RGB) resulting to greater picture resolution and elimination ofartifacts associated with traditional composite video signals.AUDIO SETUP MENUdigital audio outputEach DVD disc has a variety of audio output options. Set the player’s DigitalAudio Output according to the type of audio system you use.dolbY digital/pcm: Select DOLBY DIGITAL/PCM if an active digitaloutput is supplied to a Dolby Digital decoder (or an amplifier or otherequipment with Dolby Digital decoder). In this mode, the T 585 willautomatically switch between Dolby Digital and PCM depending onthe program encoded on the disc, with Dolby Digital given priority. DTSis not possible with this setting.Stream/pcm: Select Stream/PCM if an active digital output is suppliedto an amplifier or other equipment with DTS decoder, Dolby Digitaldecoder and MPEG decoder. If the disc is neither of stream or PCMformat, there will be no audio output at this option.pcm: Select when connected to a two-channel digital stereo amplifier.DVDs encoded in Dolby Digital or MPEG will be automaticallydownmixed to two-channel PCM audio. DTS cannot be downmixed totwo-channel PCM.off: Select to turn off digital audio output. With this option, you willhave purely analog audio output.NOTES• If an active digital audio output signal is supplied to a receiver or otherequipment without a corresponding digital decoding capability, a veryloud noise may be produced which could permanently damage thespeakers.• The DTS DVD disc sound is played back only when the DVD player isconnected to a receiver with a DTS decoder.5.1 Speaker SetupThis option allows you to configure the 5.1 CHANNEL AUDIO OUT of theT 585. Digital audio output will not be affected by the settings done in thissection. Use [ ] keys to select a menu item and [ ] keys to adjustthe settings of the selected item.Speaker SelectionSelect a speaker that you want to adjust - Front L, Center, Front R, Rear R,Rear L or Subwoofer.SizeSmall: Select if you have connected to a system with speakers that lackssignificant deep bass response - about 150Hz below.large: Select if you have connected to a system with full frequencyspeakers capable of deep bass response.none: Select when you do not have a certain speaker connected.Front L/R speaker’s size can only be set to “Large” or “Small”. If Front L/Rspeaker’s size is set to “Small”, Rear and Centre speaker’s size can only be setto “Small” or “None”.Subwoofer’s size can be set only to “Large” or “None”.volumeAdjust the output level of the selected speaker from -10dB up to amaximum of 0dB.diStanceSetting the Distance lets the speakers know how far the sound has to travelto reach your set listening point. This allows the sound from each speaker toreach the listener at the same time.Distance can be adjusted within 1ft (0.30m) up to 20ft (6m).DISTANCE setting is not applicable for Subwoofer.OPERATIONuSing the t 585 – Setup menu1ENGLISHFRANÇAISESPAÑOLITALIANODEUTSCHNEDERLANDSSVENSKAРУССКИЙ