NAD T585 Owner's Manual

Also see for T 585: Catalog Owner's manual Specifications Service manual Technical bulletin

NAD T585 Owner's Manual Manual pdf 8 page image

IDENTIFICATION OF CONTROLSrear panel1 rS-232: Connect this interface via RS-232 serial cable (not supplied)to any Windows® compatible PC to allow remote control of the T 585through NAD’s proprietary PC software or other compatible externalcontrollers.Please log on to www.nadelectronics.com/software for the latest PCinterface control software.NAD is a certified partner of AMX and Crestron and fully supports theseexternal devices. See your NAD audio specialist for more information.2 ext ir in: This input is connected to the output of an IR (infrared)repeater (Xantech or similar) or the IR output of another component toallow control of the T 585 from a remote location.Most NAD products with IR OUT are fully compatible with the T 585.3 digital out (coaxial, optical): Connect the optical or coaxialdigital OUT ports to the corresponding S/PDIF digital input of acompatible device such as CD recorders, receivers, computer soundcardor other digital processors.4 mixed audio out: Connect to the corresponding analog audioinput of an amplifier, receiver or stereo system.5 5.1ch audio out: The T 585 contains a multi-channel decoder. Itenables playback of discs recorded in multi-channel surround withoutthe need for an optional decoder.Connect to the corresponding multi-channel audio input of a receiveror a processor.6 video out/S-video out: Connect to video input of a TV/monitorusing quality dual-RCA and/or S-Video cables designed for video signals.In general, the S-Video connection is superior and should be used ifyour TV/monitor provides the corresponding input.7 component video out: Connect the T 585’s COMPONENT VIDEOOUT to the component video input of a compatible TV/monitor/ oran A/V Receiver with component video input. Be sure to observeconsistency in connecting the appropriate Y, Cb/Pb, Cr/Pr jacks to thecorresponding sources/inputs. Do not rely purely on the color coding ofthe jacks, which may not always be consistent among brands.hdmi out: Using a HDMI cable (not supplied), connect the HDMI OUTjack to the corresponding HDMI input jack of an HDTV, a projector or anA/V Receiver.Set “HDMI” to “ON” at the “Video Output” section of the VIDEO SETUPmenu for audio/video to be available at HDMI OUT.Refer also to the item on VIDEO OUTPUT at the VIDEO SETUP MENUsection of the OPERATION – USING THE T 585 – SETUP MENU page.WARNINGBefore connecting and disconnecting any HDMI cables, both the T 585and the ancillary device must be powered OFF and unplugged from theAC outlet. Failure to observe this practice may cause permanent damageto all equipment connected via HDMI sockets.9 Scart/rgb out (europe model/pal only): Connect the T 585’s[SCART/RGB OUT] to the SCART/RGB video input of a compatible TV/monitor. Be sure to observe the correct orientation of the SCART/RGBplug (not supplied).10 vga output: Using a VGA cable (not supplied), connect this VGAoutput port to a VGA-compatible external monitor. This VGA port iscompatible with the following resolutions – VGA (640 x 480), XGA (1024x 768) and SXGA (1280 x 1024).Set “VGA” to “ON” at the “Video Output” section of the VIDEO SETUPmenu for video to be available at VGA OUTPUT.Refer also to the item on VIDEO OUTPUT at the VIDEO SETUP MENUsection of the OPERATION – USING THE T 585 – SETUP MENU page.3 4 5 6 7 8 101 2 11ATTENTION!Please make sure that the T 585 is powered off or unplugged before making any connections. It is also advisable to power-down or unplug all associatedcomponents while making or breaking any signal or AC power connections.12 13 1498ENGLISH FRANÇAIS ESPAÑOL ITALIANO DEUTSCH NEDERLANDS SVENSKA РУССКИЙRefer also to the item on VIDEO OUTPUT at the VIDEO SETUP MENUsection of the OPERATION - USING THE T 585 - SETUP MENU page.8