|
– 147 –Chapter 7 Display — Screen status displayNo Item Shooting PlaybackMODE CHK>:CHK>: : [OTHER DISPLAY][ALL] [PARTIAL] [USER]35 Recording media display l — l — l l l36 Simultaneous recording mode display l — l — l — l37 High-sensitivity mode display l — l — l l l38 One clip recording mode status display l — l — l l l39 Recording/playback operation statusdisplay l l l —*3 l l l40 switch operationdisplay l — l — l l l41 GPS display l — l — l — l42 Audio monitor volume adjustmentdisplay l l —* 1 —* 1 —* 1 —* 1 —* 143 Front audio level volume display l — —* 1 —* 1 —* 1 —* 1 —* 1*1 May be displayed depending on other settings.*2 Displayed when the remaining capacity becomes smaller.*3 Displayed during shooting.Mode check displayThe camera settings and status can be displayed on the viewfinder or LCD monitor screen for check.Each time the switch on the camera is pushed towards the side, the five screens are switched.[STATUS] screen display → [FUNCTION] screen display → [AUDIO] screen display → [USER SW] screen display → [META INFO] screen display → nodisplayEach screen is displayed for approximately five seconds. Pushing the switch towards the side while the screen is displayedmoves to the next screen.[FUNCTION] screenDisplays the video output status and information of the recording media.[SDI OUT] — Displays the status of the signal output from the terminal.[TYPE] Displays the format of the signal output from the terminal by [HD-SDI]/[SD-SDI].[CHAR] Displays the superimposition status of characters selected in the main menu → [OUTPUTSEL] → [SDI OUT CHAR] by [ON]/[OFF].[P2CARD STATUS]—Displays the status of the P2 card inserted in the card slot, remaining capacity, and totalused capacity.The statuses of cards to be displayed are as follows:[ACTIVE]/[ACCESSING]/[INFO READING]/[FULL]/[PROTECTED]/[NOT SUPPORTED]/[FORMAT ERROR]/[AUTH NG]/[REC IMPOSSIBLE]/[NO CARD]For details, refer to “P2 card access LEDs and status of P2 cards” (page 35).[TOTAL P2/mP2] Displays the remaining capacity/total capacity totaled for slots 1 and 2 (or slots 3) and therecording media ([P2] or [mP2]).[SLOT1] Displays the status of the microP2 memory card in slot 1 and remaining capacity/totalcapacity.[SLOT2] Displays the status of the microP2 memory card in slot 2 and remaining capacity/totalcapacity.[SLOT3] Displays the status of the P2 memory card in slot 3 and remaining capacity/total capacity.[PROXY] [MEDIA] Displays the media selection status for proxy recording.[P2]/[P2&SD]/[OFF][MODE] Displays the setting status for proxy recording mode.[AVC-G6 2CH MOV]/[SHQ 2CH MOV]/[HQ 2CH MOV]/[LOW 2CH MOV][PROXY ERROR] Displays the operation error on the proxy module.[NETWORK] [NETWORK] Displays the network to be used and its status.[AUDIO] screenDisplays audio settings and the selection status of each recording channel.[AUDIO][INT MIC]Displays the built-in microphone status set in the main menu → [AUDIO SETUP] → [INPUTSETTING] → [INT MIC].f [STEREO]: Records audio from two directions in the front with the 2ch stereomicrophone.f [MONO]: This mode records clearer audio from the front by enhancing the directionalityforward like a shotgun microphone. Audio recorded on the left and right are the same.f [OFF]: Disables audio of the built-in microphone.[AUDIO OUT]Displays the audio input signal status set in the main menu → [AUDIO SETUP] →[OUTPUT SETTING] → [AUDIO OUT].[CH1/CH2]/[CH1]/[CH2]/[CH3/CH4]/[CH3]/[CH4][A.IN] [CH1/2/3/4] Displays the input status of each channel.[INT(L)]/[INT(R)]/[INPUT1]/[INPUT2]
|
