Installation InstructionsInstallation precautionsPanasonic does not accept any responsibility for accident or damage during installation if procedure in this manual is notfollowed.To installation personnelRead the “Installation Instructions” thoroughly and then perform the operation correctly and safely.Also, always read the “Read this first!” (→ page 4) of this manual as they contain important information.After the installation, give the “Installation Instructions” to the customer to save for future use. Ensure that the installation work complies withthe technical standards governing electricalequipment. This unit is for indoor use only.It cannot be used outdoors.Avoid installation in a location where the unit will be exposed todirect sunlight for extended periods or near a cooling or heatingappliance.Otherwise, deformation, discoloration, malfunctioning and/orproblems in operation may result. Operate the unit where it will notbe splashed or sprayed by water. Use the unit with an installation where the unitis suspended from an overhead surface orstanding.Do not use the unit on its side or tilted at an angle.• Be absolutely sure to use the bracket mounting screws supplied withthe unit to mount the bracket.Do not use wood screws, nails, etc.In the case of a concrete ceiling, secure the unit using anchor bolts(for M4) or AY plug bolts (for M4).Recommended tightening torque M4 · 1.47 N · m {15 kgf · cm}• The withdrawal strength of the mounting location for each screwmust be at least 294 N {30 kgf}.• When mounting the unit on a ceiling made of plasterboard, forinstance, if it is not strong enough to support its weight, eitherreinforce the ceiling adequately or use the WV-Q105A direct ceilingmount bracket, which is sold separately.• When using a mount bracket which is sold separately, read thehandling instructions.• Do not hold the camera head while undertaking the installation work.Doing so may cause malfunctioning.OK NG OK NGStanding installation Suspended installation Concerning the installation locationInstall the unit in a stable location which will not be susceptible toshaking. If the unit is installed in a location which is susceptible toshaking, this will cause the unit’s images to shake in turn.Install the unit on a ceiling that is strong enough (such as a concreteceiling).If the unit is to be installed on a ceiling which is not strong enough,reinforce the ceiling sufficiently first. Do not install or use the unit in the followingkinds of locations.• On walls (where the unit would be installed sideways)• In locations (including places such as under the eaves of abuilding) where the unit would be directly exposed to rain or water• In locations such as kitchens where there are high concentrationsof steam and grease• In outdoor locations or hot places where the temperature willexceed 40°C (104°F)• In cold locations where the temperature will drop below 0°C(32°F)• In locations where the humidity will exceed 80%• In locations where chemicals are used such as near swimmingpools• At sea, in coastal areas or in locations where corrosive gases areemitted• In locations where radiation, X-rays, or strong radio waves ormagnetic fields are generated• In locations where the unit would be subject to a great dealof vibration such as on board a vehicle or ship (this unit is notdesigned to be used in vehicles)• In locations where the temperature is subject to sudden changessuch as near the air outlet of an air conditioner or near a doorwhich allows the outside air to come in What to avoid to ensure that the unit willperform stably over a prolonged period.• Using the unit for a prolonged period in a location with hightemperature and humidity levels will cause its parts to deteriorateand shorten its service life.• Ensure that a cooling unit or heating unit will not blow any airdirectly toward the installation location. Be absolutely sure to use the supplied bracketsand screws to install the camera.• Do not mount the unit by employing any methods other than thosespecified.• Do not remodel the mounting bracket or mounting screws providedwith the unit.AW‑HEA10main unitMounting conditionsApplicable mount bracket Mounting onto the ceilingMass Model No. Mass Mounting RecommendedscrewsNo. ofscrewsMinimum withdrawal strength(per screw)Approx. 0.9 kg(1.98 lb)(Including mountbracket)Direct mount(suppliedaccessory)Approx.0.3 kg(0.66 lb)Suspended/Standing M4 screws (suppliedaccessory) 4 294 N {30 kgf}• Ensure that the mounting strengthcan support a weight that is at leastfive times the total mass when theunit and HD integrated camera aremounted.WV-Q105A(optionalaccessory)Approx.0.15 kg(0.33 lb)For ceilingM4 screws(supplied with theWV-Q105A)45
