Panasonic DMR-EH75VS Operating Instructions Manual

Contents

Panasonic DMR-EH75VS Operating Instructions Manual Manual pdf 79 page image

79RQT8346Channel/Clock settings when TV Guide On Screen® system is not usedRefer to the control reference on page 74.Preparation:If the program listings has already been downloaded, return the unit to the factory preset condition using the steps indicated below.When the unit is on and stopped1 Press and hold [CH, X] and [CH, W] on the main unit for about 5 seconds.The unit turns off.2 Press [Í, DVD/VHS POWER] to turn the unit on.3 After the language and TV aspect is setup, press [RETURN] and exit the TV GuideOn Screen® system setup screen.NoteYou can set scheduled recording only manually after you set the unit with “Set ChannelsAutomatically”.[1] While stoppedPress [FUNCTIONS].[2] Press [3, 4] to select “Other Functions” andthen press [ENTER].[3] Press [3, 4] to select “Setup” and then press[ENTER].[4] Press [3, 4] to select “Channel” and thenpress [1].[5] Press [3, 4] to select “Set ChannelsAutomatically” and then press [ENTER].[6] Press [ENTER].Auto Channel Setting starts. This takes a few minutes.The unit then proceeds with Auto Clock Setting. The time isdisplayed when finished.≥DST, Daylight Saving Time, shows the summertime setting.≥TIME ZONE shows the time difference from Greenwich MeanTime (GMT).EST (Eastern Standard Time) l GMT j5CST (Central Standard Time) l GMT j6MST (Mountain Standard Time) l GMT j7PST (Pacific Standard Time) l GMT j8AST (Alaska Standard Time) l GMT j9HST (Hawaii Standard Time) l GMT j10For other areas: xx hr≥If the Auto Clock Setting does not start automatically, select“Clock Settings” from the “Setup” tab and then select “SetClock Automatically”.≥If the time was not set correctly, use manual clock setting(l 25) or adjust time zone.[7] Press [ENTER].≥Regarding DST (Daylight Saving Time) l 25≥The unit configures channels according to the Signal Source(RF IN) settings as follows.Adjust the time zone (j1 or i1) if it was not set correctly with autoclock setting.You cannot change this setting if you set the clock manually.[1] While stoppedPress [FUNCTIONS].[2] Press [3, 4] to select “Other Functions” andthen press [ENTER].[3] Press [3, 4] to select “Setup” and then press[ENTER].[4] Press [3, 4] to select “Setup” and then press[1].[5] Press [3, 4] to select “Clock Settings” andthen press [ENTER].[6] Press [3, 4] to select “Adjust Time Zone” andthen press [ENTER].≥Regarding DST (Daylight Saving Time) l 25[7] Press [3, 4] to select “s1” or “r1” and thenpress [ENTER].To return to the previous screenPress [RETURN].To exit the screenPress [RETURN] several times.To cancel partway while Auto Channel/Clock Setting is taking placePress [RETURN].To set so the TV Guide On Screen ® system is not displayed automatically when you turn the unit onWhen the power is turned on and the Start setup screen is displayed, press [3, 4] to select “Don’t remind me again” and press [ENTER].Auto channel/clock settingsSetupDiscChannelVideoAudioDisplaySet Clock AutomaticallyAuto Clock Setting is complete.11/4/2006 12:15 AMDST.............. OnTime Zone..... CSTSetupSignal Source(RF IN) Band ChannelAntenna VHF 2 to 13UHF 14 to 69CableTVVHF 2 to 13CATV LOW BAND 95 to 99CATV MID/SUPER BAND 14 to 36CATV HYPER BAND 37 to 65ULTRA BAND 66 to 94100 to 125SPECIAL CATV CHANNEL 1∫ Adjust Time ZoneSetupSetupAudioAdjust Time Zonej10i1ChannelDiscVideoChanging the unit’s settings/Channel/Clock settings when TV Guide On Screen® system is not used