Panasonic LQ-MD800 Operating Instructions Manual

Also see for LQ-MD800: Specifications Operating instructions

– 13 –Connecting and Setting up (continued)COMPONENT VIDEO OUT terminalThese terminals can be used for either interlace or progressiveoutput and provide a purer picture than the S-VIDEO OUTterminal.Connection using these terminals outputs the color differencesignals (PB/PR) and luminance signal (Y) separately in order toachieve high fidelity in reproducing colors.• The description of the component video input terminalsdepends on the monitor television (e.g., Y/P B /P R , Y/B-Y/R-Y,Y/C B/CR).To watch progressive video (NTSC only)Connect to the component video (480P) input terminals on amonitor television compatible with this unit's copy guard system.(Video will not be displayed correctly if connected to anincompatible monitor television.)• All Panasonic monitor televisions that have 480P inputterminals are compatible. Consult the manufacturer if you haveanother brand of monitor television.Regarding Progressive Television PictureProgressive image aspect (height to width ratio) is set at astandard 16:9. DVD-Video which has been set at 16:9 will bedisplayed correctly. However, 4:3 video material will bestretched to the right and left when displayed.To view the picture at the right aspect• For monitor televisions that allow the aspect of progressiveimages to be adjusted, use the function provided on themonitor television and adjust as necessary.• For monitor televisions which do not allow the aspect ofprogressive images to be adjusted, please set “Progressive(NTSC)” to “Off”.Note:• If the unit is connected to the TV through VIDEO OUT or S-VIDEO OUT, output signal will be interlace only (even if youselect progressive output). DV terminalDV cable (4P-4P or 4P-6P)AC mains lead (supplied)Notes:• Be sure to observe the following points when connecting theIEEE1394 cable (DV cable).· This unit and all connected equipment should be used with a sharedGND connection. If all equipment is not connected to a shared GND,turn off the power to all equipment before connecting or removing theIEEE1394 cable.· When connecting to equipment having a 6-pin terminal, connect theIEEE1394 cable to the 6-pin terminal first and then to the terminal onthis unit.· When connecting to equipment having a 6-pin terminal, be sure toconnect the end of the IEEE1394 cable that matches the terminalshape. Inserting the wrong end of the plug can damage the unit.• The DV input on this unit is for use with DV equipment only.• When DV equipment is connected, it is not possible to operatethe unit from the other equipment.• Only one piece of DV equipment (e.g., Digital Video Camera)can be connected to the unit via the DV Input terminal.• The picture compression system of the DV equipment you haveconnected may differ from that used in this unit. In such cases,dubbing from this equipment will not be possible.S-Video, stereo audio terminalsS-Video cable (4P)Stereo Audio cable (PHONO x 2)AC mains lead (supplied)Composite video, stereo audio terminalsVideo cable (BNC)Stereo Audio cable (PHONO x 2)AC mains lead (supplied)Connecting a video playerVIDEOVIDEOS-VIDEOS-VIDEO12YCH1(A)DV IN RS-232C USB~ AC INPAUSEREMOTECH2(B) CH1 CH2PB P RVIDEO INVIDEO OUTAUDIO IN AUDIO OUT AUDIOMONVIDEOVIDEOS-VIDEOS-VIDEO12YCH1(A)DV IN RS-232C USB~ AC INPAUSEREMOTECH2(B) CH1 CH2PB P RVIDEO INVIDEO OUTAUDIO IN AUDIO OUT AUDIOMONVIDEOVIDEOS-VIDEOS-VIDEO12YCH1(A)DV IN RS-232C USB~ AC INPAUSEREMOTECH2(B) CH1 CH2PB P RVIDEO INVIDEO OUTAUDIO IN AUDIO OUT AUDIOMONDV INDV OUTVIDEOINVIDEOOUTS-VIDEOINS-VIDEOOUTVideo playerVideo playerVideo playerAUDIO INAUDIOOUTAUDIOOUT AUDIO IN