Chapter 4 Settings — [ADVANCED MENU] menuENGLISH - 8715) Press as to select [UPPER], [LOWER], [LEFT], or [RIGHT] in [BLACK BORDER WIDTH]16) Press qw to set the region (width) of the [BLACK BORDER WIDTH] adjustment.f When PT-DZ870E is used, proceed to Step 17).f When PT-DW830E or PT-DX100E is used, proceed to Step 19).17) Press as to select [UPPER KEYSTONE AREA], [LOWER KEYSTONE AREA], [LEFT KEYSTONEAREA], or [RIGHT KEYSTONE AREA].18) Press qw to adjust the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACKBORDER LEVEL].19) Press as to select [BLACK BORDER LEVEL].20) Press the button.f The [BLACK BORDER LEVEL] screen is displayed.f If [INTERLOCKED] is set to [OFF], [RED], [GREEN], and [BLUE] can be adjusted individually.21) Press as to select an item, and press qw to adjust the setting.[BLACK BORDER WIDTH] (Right)Projection range Edge blending [WIDTH] (Right)[MARKER] (Red)Edge blending [START] (Right)([MARKER] (Green))[BLACK BORDER LEVEL][OVERLAPPED BLACK LEVEL] (Right)[NON-OVERLAPPED BLACK LEVEL]Notef [BRIGHTNESS ADJUST] is a function that makes the increased brightness in black level of the overlapping image area difficult to noticewhen [EDGE BLENDING] is used to configure multiple screens. The optimal point of correction is set by adjusting [NON-OVERLAPPEDBLACK LEVEL] so the black level of the overlapping image area will be the same level as the non-overlapping area. If the border area of thepart where the image is overlapping and the non-overlapping part gets brighter after adjusting [NON-OVERLAPPED BLACK LEVEL], adjustthe width of the top, bottom, left, or right. Adjust [BLACK BORDER LEVEL] when the width adjustment makes only the border area darker.f The joining part may look discontinuous depending on the position you are looking from when a screen with high gain or rear screen is used.f When configuring multiple screens using both horizontal and vertical edge blending, adjust [OVERLAPPED BLACK LEVEL] first beforemaking adjustments in Step 12). Adjustment method is same as the procedure of [NON-OVERLAPPED BLACK LEVEL].f If only horizontal or vertical edge blending is used, set all items in [OVERLAPPED BLACK LEVEL] to 0.f [AUTO TESTPATTERN] settings change together with the [AUTO TESTPATTERN] of [COLOR MATCHING].f Adjustment of the tilt of the border between [NON-OVERLAPPED BLACK LEVEL] and [BLACK BORDER LEVEL] is a function to performthe adjustment of [GEOMETRY(2D)] (x page 80) together with the edge blending. If [NON-OVERLAPPED BLACK LEVEL] is tilted bycorrecting the keystone distortion from [KEYSTONE] in [GEOMETRY(2D)], perform Steps 17)18) to adjust the edge blending according tothe shape of [NON-OVERLAPPED BLACK LEVEL].f When the keystone is corrected with [KEYSTONE(3D)], the edge blending cannot be adjusted together. (Only for PT-DZ870E)f When the keystone is corrected with [KEYSTONE], the edge blending cannot be adjusted together. (Only for PT-DW830E, PT-DX100E)[FRAME RESPONSE]Set image frame delay.1) Press as to select [FRAME RESPONSE].2) Press qw to switch the item.f The items will switch each time you press the button.[NORMAL] Standard setting.[FAST]*1 Simplifies the image processing to reduce image frame delay.[FIXED]*2 Sets image frame delay to be constant regardless of the image position or magnification.*1 When input signals are other than interlaced signals, [FAST] cannot be set.*2 Only when movie-based signals and still image signals with the vertical scanning frequency of 50 Hz or 60 Hz are inputNotef When [FRAME RESPONSE] is set to [FAST], picture quality deteriorates. Also, [DIGITAL CINEMA REALITY] cannot be set.f [FRAME RESPONSE] cannot be set during P IN P.
