Panasonic WJ-HD220 Operating Instructions Manual

Also see for WJHD220 - DIGITAL DISK RECORDER: Reference Reference Specifications Brochure & specs Operating instructions

Contents

Panasonic WJ-HD220 Operating Instructions Manual Manual pdf 27 page image

27 Post-alarm Recording (POST ALMREC)This setting specifies the duration of alarm recording afteran alarm input. Functions active during alarm recording arebuzzer beeping, ALARM LED indication, "ALARM" statusdisplay, and the ALARM OUT signal.1. Move the cursor to POST ALARM REC with the [D] or[C] button.2. Select the desired duration with the JogDial.The default value is 10 seconds.The unit will revert to the previous status when the timehas elapsed.Available times (seconds): 5, 10, 20, 30Available times (minutes): 1, 1.5, 2, 3, 6Continue: Recording continues until the [RESET] but-ton is pressed, or the RESET IN signal is supplied tothe rear panel.Manual: Recording continues for as long as the alarminput is active, or at least for 10 seconds if the inputturns inactive earlier. Dynamic Recording (DYNAMIC REC)This setting specifies the recording pattern on the diskwhen one or more alarms operate.1. Move the cursor to DYNAMIC REC with the [D] or [C]button.2. Select the parameter with the JogDial, and press theJogDial.The default is OFF.ALM-MULTI: Alarmed channels are recorded with pri-ority over others.OFF: All channels are recorded with the same priority. Trigger Action Setup (TRIGGERACTION SETUP)This setting specifies the two roles of alarm recording andalarm control functions (Refer to page 47) in the post-alarmsequence.When combination cameras are connected to VIDEO IN 1-4on the rear panel, you can select a preset position for cam-eras 1-4. The camera will move to the preset position whenan alarm other than VMD arises for the camera.Notes:• The preset position assignment on the TRIGGERACTION SETUP menu is not available for each PROG n(1 - 4) SETUP menu, but available only for the RECSETUP menu.• You need to preset desired positions for the cameraprior to operation.• VMD will not move the camera to the preset position.1. Move the cursor to TRIGGER ACTION SETUPO, andpress the JogDial.The TRIGGER ACTION SETUP menu opens.2. Move the cursor to the channel.3. Select a mode with the JogDial, and press the JogDial.The default is REC&ALM.OFF: Disables alarm recording or warning.REC&ALM: Enables both alarm recording and warning.REC: Enables alarm recording, but disables warning.4. The cursor is at the PRESET column. Select a presetparameter with the JogDial, and press the JogDial.1-64: Moves the camera to the specified preset posi-tion.HOME: Moves the camera to the home position.– –: Does not move the camera.5. Repeat steps 2, 3 and 4 until all channels are set.6. Press the [SETUP/ESC] button to return to the PROG1SETUP, NO. 1 menu. Camera Recording Setup (CAM RECSETUP)This setting is provided for the purpose of saving diskspace. Setting allows each camera channel to be enrolledin all recording modes or exclusively in alarm recording.1. Move the cursor to CAM REC SETUP, and press the[SET] button. The CAM REC SETUP menu opens.2. Move the cursor to the camera channel with the [D] or[C] button.CAM REC SETUPCAM MODE1 REC2 REC3 REC4 ALM-ONLY5 REC6 ALM-ONLY7 REC8 RECTRIGGER ACTION SETUPCAM MODE PRESET1→ REC&ALM ––2→ REC&ALM ––3→ REC&ALM ––4→ REC&ALM ––5→ REC&ALM6→ REC&ALM7→ REC&ALM8→ REC&ALM