GB-7RANSOMES COMMANDER 3520SAFETY, OPERATORS & MAINTENANCE MANUAL4 SPECIFICATIONS4.1 ENGINE SPECIFICATIONTYPE:: Kubota 38KW (51HP) , 4cylinder (in line) vertical Dieselengine, 4 stroke, water cooled,2197cc (134.06 cu.in) with 12Velectric start.Model: V2203 -E2B-RANUK-1Maximum Speed: 2800 +50, - 0 RPM (No load)Idle Speed: 1400 ± 50 RPMOil Sump Capacity:9.5 litres (16.72 Imp.pints)(20.08 US pints)Firing Order: 1, 3, 4, 2.Fuel: No. 2-D Diesel fuel (ASTM D975)4.2 MACHINE SPECIFICATIONFrame construction:Heavy duty fabricated steelchassis.Transmission:Hydrostatic power provided by aservo-controlled transmissionpump. Driving 4 individual wheelmotors with selectable 2 or4WD.Cutting unit drive:Hydraulic, with forward, neutral,reverse control valve. Floormounted switch for cylinderengage. Hand control valve forreel speed adjustment.Speeds:Cutting: 12 km/h (7 mph)Transport: 25 kp/h (15 mph)Reverse: 6 kp/h (4 mph)Steering: Hydrostatic power steering torear wheels.Ground pressure: 1.0 kg/cm (14.5p.s.i)Brakes, Service: Positive hydostatic braking.Parking: Fail safe, Oil immersed wet discbrakes.Capacities:Cooling System: 6.8 litres (12 Imp. pints)(14.4 US pints)Fuel Tank: 60 litres (13.2 Imp. galls)(13.7 US galls)Hydraulic Tank: 52 litres (11.4 Imp. galls)(15.8 US galls)Battery: 6654.3 DIMENSIONSWidth of cut: 3.50 metres (138in)Overall width: 2.00 metres (78.8in) min(transport)Overall height: 1.45 metres (57in)Overall length; 3.10 metres (123 in)Overall weight ofmachine: 2080kg (4576lbs)**With Sport 200 8-knife floating head units.Wheel Track: 1.5 metres (59in)Wheel Base: 1.65 metres (65in)Ground Clearance: 161mm (6 5/16in)*4.4 VIBRATION LEVELThe machine was tested for whole body and hand/arm vibration levels. The operator was seated in thenormal operating position with both hands on thesteering mechanism. The engine was running andthe cutting device was rotating with the machinestationary.Hand / Arm acceleration level : 0.741 m/s2Whole body acceleration level m/s 24.5 SLOPESDO NOT USE ON SLOPES GREATER THAN 15°The slope 15° was calculated using static stabilitymeasurements according to the requirements ofEN 836.4.6 RECOMMENDED LUBRICANTSEngine oil: Should be to MIL-L-2104C or toA.P.I. Classification SE/SF/SGgrades. [10W-30]Hydraulic Oil: Shell Tellus 46 to ISO VG46, orequivalent.Grease: Shell Darina R2, or equivalent.noitacoLroolF noitacoLtaeSx y z x y znaeM 2510.0 2820.0 9830.0 10.0 5910.0 5130.0SERUSSERPERYTtcudorPleehWtnorF leehWraeReziSeryT epyTeryT erusserPeryT eziSeryT epyTeryT erusserPeryT0253rednammoC 21-00.21x62rp6carTitluMnatiT isp02-41 rab73.1-00.121-05.01x32rp6carTitluMnatiT isp02-41 rab73.1-00.1)ralveK(xxamfruTsixxaMrp4s561-Cnrettapdaert isp22-02 rab05.1-73.1 )ralveK(xxamfruTsixxaMrp4s561-Cnrettapdaert isp22-02 rab05.1-73.1