Regency U41 Owners & Installation Manual

Also see for U41: Owners & installation manual

Contents

Regency U41 Owners & Installation Manual Manual pdf 17 page image

17Regency U41-3 ULTIMATE Gas Fireplace InsertInstalling Glass1) Install both center and side glass ontoextrusions as per diagram.2) Place glass assembly into door frame.3) Install retainers by placing 1 drop of gluewhere previously glued and put in place.4) Install side retainers.5) Install door catch plate.6) Install the 24 nuts loosely, do not tighten yet.7) Tighten side panels nuts using the followingprocedure:a. tighten top &bottom outsidecorner nuts (2)b. tighten insidenuts (3)c. tighten top &bottom insidecorners (2)GLASSREPLACEMENTYour Regency stove is supplied with hightemperature, 5 mm Neoceram ceramic glassthat will withstand the highest heat that yourunit will produce. In the event that you breakyour glass by impact, purchase your replace-ment from an authorized Regency dealer only,and follow our step-by-step instructions forreplacement.LOG REPLACEMENTThe unit should never be used with broken logs.Turn off the gas valve and allow the unit to coolbefore opening door to carefully remove thelogs. The pilot light generates enough heat toburn someone. If for any reason a log shouldneed replacement, you must use the properreplacement log. The position of these logsmust be as shown in the diagram under LogInstallation.NOTE: Improper positioning of logs maycreate carbon build-up and willalter the unit’s performance whichis not covered under warranty.GOLD-PLATED DOORSThe 24 carat gold plated finish on the doorrequires little maintenance, and need only becleaned with a damp cloth. DO NOT useabrasive materials or chemical cleaners, asthey may harm the finish and void the warranty.Clean any fingerprints off before turning theunit on. If gasket seal is not tight - doormay discolour.DOOR GASKET ANDGLASS GASKETIf the door gasket requires replacement use 7/8" diameter oval door gasket (Part # 650-920).The glass requires 5/8" flat glass gasket (Part# 936-243). See your Regency Dealer.LATCH ADJUSTMENTThe door latch may require adjustment as thedoor gasket material compresses after a fewfires and after glassreplacement. Turn theadjustable latch to tight-en or loosen the latch.8) Tighten the 10 nuts on center glass retain-er.9) Repeat step 7 for other side panel.10) Replace new gasket by gluing it in place.11) Install door onto stove and check the seal.PANEL DOOR1) Remove the door from the unit and place ona soft surface to prevent scratching.2) Pull out the door gasket.3) Remove the nuts holding the glass retain-ers in place.4) Remove the glass retainers (sides, top andbottom) and the door catch plate.5) Replace the glass. The glass must havegasketing around it.6) Reverse the previous steps, replace theretainers and fasten with the nuts but donot overtighten, as this can break the glass.Note: the door catch plate fits on top of theleft side retainer.7) Put gasket glue on the retainers, but do notput glue on the screws. Replace the doorgasket, the two ends butt tight together onthe bottom edge of the door.8) Replace door on the stove and check theseal.MITRED DOORRemoving GlassNote: Wearing gloves will protect yourhands while handling glass.1) Remove the door from the unit and place ona soft surface to prevent scratching.2) Pull out the door gasket.3) Remove the 24 nuts holding the glass retain-ers in place. Do not remove the nuts under-neath the retainers.4) Remove the door catch plate.5) Remove glass retainers on sides first (3each side) then remove two center retain-ers.Note: Center glass retainers are glued tocenter glass.6) Remove glass from extrusions. When re-moving center glass, leave white insulationin place.MAINTENANCE