YASKAWA MECHATROLINK-II SI-T3 Technical Manual Manual pdf 22 page image
Manuals database logo
manualsdatabase
Your AI-powered manual search engine

YASKAWA MECHATROLINK-II SI-T3 Technical Manual

Also see for SI-T3 MECHATROLINK-II A1000 Series: Installation manualTechnical manualInstallation manualInstallation manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 previewPage 36 previewPage 37 previewPage 38 previewPage 39 previewPage 40 previewPage 41 previewPage 42 previewPage 43 previewPage 44 previewPage 45 previewPage 46 previewPage 47 previewPage 48 preview
Contents
  1. Table Of Contents
  2. Table Of Contents
  3. Preface and Safety
  4. Supplemental Safety Information
  5. Install the Option on a GA500 Drive
  6. Receiving
  7. Drive Components with Option
  8. MECHATROLINK-II Option LED Display
  9. Procedures for Installing and Wiring Options on a Drive
  10. Procedure B
  11. MECHATROLINK-II Communications Cables
  12. Option Connection Diagram
  13. Transmission Interface
  14. Communication Phases
  15. Phase 1: Initial status after power ON
  16. MECHATROLINK-II Commands
  17. PRM_WR: 02 (Hex.) (Write Parameter)
  18. CONFIG: 04 (Hex.) (RAM Write and EEPROM Write)
  19. ALM_RD: 05 (Hex.) (Read Alarm and Warning)
  20. ALM_CLR: 06 (Hex.) (Clear Alarm and Warning)
  21. CONNECT: 0E (Hex.) (Connect)
  22. DISCONNECT: 0F (Hex.) (Disconnect)
  23. Sub-Commands
  25. STATUS Field
  26. Troubleshooting
  27. Other Faults
  28. Drive-Side Error Codes
  29. Minor Faults and Alarms
  30. EMC Guidelines Compliance
  31. Specifications
  32. Disposal
  33. Revision History
YASKAWA MECHATROLINK-II SI-T3 Technical Manual Manual pdf 22 page image
7 Transmission Interface22 YASKAWA SIEP C730600 86F MECHATROLINK-II Technical ManualFigure 7.1 Basic Format of Data Transfer (17-Byte Data Transmission)Figure 7.2 Basic Format of Data Transfer (32-Byte Data Transmission)ā—† Communication PhasesThe SI-T3 option changes status after it receives a command code or fault from the master as shown in the figure.The communication phases determine the available commands. Refer to Table 7.1 and Table 7.2 for moreinformation.
/ 48
Related manuals for YASKAWA SI-T3 MECHATROLINK-II A1000 Series
YASKAWA SI-ET3 Technical Manual first page preview
YASKAWA SI-ET3 Technical Manual
YASKAWA SI-P3 Technical Manual first page preview
YASKAWA SI-P3 Technical Manual
YASKAWA SI-EM3 Technical Manual first page preview
YASKAWA SI-EM3 Technical Manual
YASKAWA SI-EP3 Technical Manual first page preview
YASKAWA SI-EP3 Technical Manual
YASKAWA SI-EN3 Technical Manual first page preview
YASKAWA SI-EN3 Technical Manual
YASKAWA SI-EP3 Technical Manual first page preview
YASKAWA SI-EP3 Technical Manual
YASKAWA SI-EN3 Technical Manual first page preview
YASKAWA SI-EN3 Technical Manual
YASKAWA SI-EL3 Technical Manual first page preview
YASKAWA SI-EL3 Technical Manual
YASKAWA CC-Link Technical Manual first page preview
YASKAWA CC-Link Technical Manual
YASKAWA F7 Technical Manual first page preview
YASKAWA F7 Technical Manual
This manual is suitable for:
SI-T3 MECHATROLINK-II A1000 Series
Manuals database logo
manualsdatabase
Your AI-powered manual search engine