Yaesu FT-1900E Operating Manual

70 FT-1900E OPERATING MANUALThe FT-1900E Set (Menu) mode, already described in parts of many previous chapters, iseasy to activate and set. It may be used for configuration of a wide variety of transceiverparameters, some of which have not been detailed previously. Use the following procedureto activate the Set (Menu) mode:1. Press and hold in the [MHz(SET)] key for one second to enter the Set mode.2. Rotate the DIAL knob to select the Menu Item to be adjusted.3. Press the [MHz(SET)] key momentarily to enable adjustment of the selected Menuitem, then rotate the DIAL knob to perform the actual adjustment.4. After completing your selection and adjustment, press and hold in the [MHz(SET)] keyfor one second to exit the Set mode and resume normal operation.“SET ” (MENU) M ODEMENU ITEM1 APO2 AR BEP3 AR INT4 ARS5 BCLO6 BEEP7 BELL8 BNK.LNK9 BNK NM10 CLK.SFT11 CW ID12 CWTRNG13 DC VLT14 DCS CD15 DCS RV16 DIMMER17 DT A/M18 DT DLY19 DT SET20 DT SPD21 EDG.BEP22 INT CD23 INT MD24 INT.A/M25 INT.SET26 LOCK27 MCGAIN28 MEM.SCNAVAILABLE VALUES30MIN / 1HOUR / 3HOUR /5HOUR / 8HOUR / OFFIN RNG / ALWAYS / OFF25SEC / 15SECON / OFFON / OFFKY+SCN / KEY / OFF1 / 3 / 5 / 8 / CNTNUE / OFF------ON / OFFON / OFF4WPM - 13WPM / 15WPM /17WPM / 20WPM / 24WPM /30WPM / 40WPM / OFF(20CPM - 65CPM (5CPM multiples)/ 75CPM / 85CPM / 100CPM /120CPM / 150CPM / 200CPM)---104 standard DCS codesENABLE / DISABLLVL 0 (OFF) - LVL 10MANUAL / AUTO50 / 250 / 450 / 750 / 1000 (ms)---50 / 100 (ms)ON / OFFDTMF 0 - DTMF 9 /DTMF A -DTMF FSRG / FRGMANUAL / AUTO---KEY / DIAL / K+D / PTT /K+P / D+P / ALLLVL 1 -LVL 9TAG1 / TAG2 / ALL CHFUNCTIONEnables/Disables the Automatic Power Off feature.Selects the Beep option during ARTS™ operation.Selects the Polling Interval during ARTS™ operation.Activates/Deactivates the Automatic Repeater Shift feature.Enables/Disables the Busy Channel Lock-Out feature.Enables/Disables the key beeper.Selects the CTCSS/DCS/EPCS Bell Ringer repetitions.Select the Memory Bank for the Memory Bank Link Scan.Programming an Alpha/Numeric label for a Memory Bank.Shifting of the CPU clock frequency.Enables/Disables the CW identifier during ARTS™ Operation.Enables/Disables the CW Training feature and selects the sendingspeed of the morse Code.Indicates the DC Supply Voltage.Setting of the DCS code.Enables/Disables “Inverted” DCS code decoding.Setting of the front panel display’s illumination level.Enables/Disables the DTMF Autodialer feature.Setting of the DTMF Autodialer’s TX Delay Time.Loading of the DTMF Autodialer Memories.Setting of the DTMF Autodialer Sending Speed.Enables/Disable the Band-edge beeper while scanning.Selects the Access Number (DTMF digit) for WiRES™ operation.Selects the Internet Link Connection mode.Enables/Disables DTMF Autodialer feature while operating on theInternet Connection feature.Selects the memory register for an Access Number (DTMF code) fornon-WiRES™ Internet Link System access.Selects the Control Locking Lockout combination.Adjust the microphone gain level.Selects the Memory Scan mode.DEFAULTOFFIN RNG25SECONOFFKY+SCNOFF------OFFOFFOFF---023DISABLLVL 5MANUAL450 (ms)---50 (ms)OFFDTMF 1SRGMANUAL---K+DLVL 5ALL CH