e-conolight E-WLT LARGE Series Installation Instructions Manual

e-conolight E-WLT LARGE Series Installation Instructions Manual Manual pdf 1 page image

Document: DateCreated By: ECO#LPN00666X0001A0_A 09-25-2019TMT 011046INSTALLATION INSTRUCTIONSE-WLT LARGE Serieswww.e-conolight.com | 888.243.9445 | FAX: 262.504.5409CAUTIONSIMPORTANT SAFEGUARDSWhen using electrical equipment, basic safetyprecautions should always be followed including thefollowing:READ AND FOLLOW ALLSAFETY INSTRUCTIONS1. DANGER- Risk of shock- Disconnect power beforeinstallation.DANGER – Risque de choc – Couper l’alimentationavant l’installation.2. This Product Must Be Installed In Accordance With TheApplicable Installation Code By A Person Familiar WithThe Construction And Operation Of The Product AndThe Hazards Involved.Ce Produit Doit Être Installé Selon Le Code D’installationPertinent, Par Une Personne Qui Connaît Bien LeProduit Et Son Fonctionnement Ainsi Que Les RisquesInhérents.3. Suitable for Wet Locations.Adspte pour les Endroits Mouiles.4. WALL MOUNT ONLY.INSTALLATION MURALE SEULEMENT.5. Suitable for maximum ambient of 40C.Peut etre utilise pour maximum 40C temperatureambiante.SAVE THESE INSTRUCTIONSFOR FUTURE REFERENCEMOUNTING OVER RECESSED JUNCTION BOXNOTE: Knockouts are provided for mounting over 3" octagonal, 4" oc-tagonal, or 4" square junction boxes.1. Remove lens assembly by loosening screws on side of frame. Donot loosen tamper proof screws on hinge side of frame. Swing lensassembly open,disconnect quick connect wiring connector(s) andlift lens assembly upward to remove from housing.2. Drill out appropriate knockouts in back box for attachment to junctionbox. Also drill knockout for wiring access.NOTE: Fixture should not be exclusively supported by junctionbox. Drill additional knockouts toward corners of fixture to provideadditional support. Do NOT drill within 1/4" (64 mm) from edges offixture.3. Pull supply leads from junction box through wall of back box. Attachback box to mounting surface using hardware (supplied by others)appropriate for mounting surface.NOTE: A high grade caulking material such as silicone rubber, shouldbe used around perimeter of back box to prevent water leakage intofixture or junction box.4. Make wiring connections per the Electrical Connections section.5. Replace the lens assembly on hinges, re-connect quick-connectwiring connectors, and swing lens into place. Re-tighten screws thatwere loosened in Step 1.1. Remove lens assembly by loosening screws on side of frame. Donot loosen tamper proof screws on hinge side of frame. Swing lensassembly open,disconnect quick connect wiring connector(s) and liftlens assembly upward to remove from housing.2. Drill knockouts in lower two corners and center top of back box toallow for attachment of back box to mounting surface.3. Attach back box to mounting surface using hardware (supplied byothers) appropriate for mounting surface.NOTE: A high grade caulking material such as silicone rubber, shouldbe used around perimeter of back box to prevent water entry.4. Remove appropriate threaded plugs on sides of fixture and routeelectrical conduit to the holes desired. Feed the supply leads throughthe conduit and into the back box.NOTE: Use of teflon tape on the conduit threads will ensure awatertight seal.5. Make wiring connections per the Electrical Connections section.6. Replace the lens assembly on hinges, re-connect quick-connectwiring connectors, and swing lens into place. Re-tighten screws thatwere loosened in Step 1.WALL MOUNTED WITH CONDUIT FEEDFixture is equipped with universal volt driver 120-277V(ie. 120V, 208V, 240V or 277V)PHASE TO NEUTRAL WIRING 120/277V1. Connect supply ground to fixture ground (green) lead.2. Connect supply common to fixture neutral (white) lead.3. Connect supply Vin to fixture hot (black) lead.Tuck all wires carefully into wiring chamber ensuring that no wiresare pinched.PHASE TO PHASE WIRING 208/240V1. Connect supply ground to fixture ground (green) lead.2. Connect supply L1 (Hot) to fixture neutral (white) lead.3. Connect supply L2 (Hot) to fixture hot (black) lead.Tuck all wires carefully into wiring chamber ensuring that no wiresare pinched.ELECTRICAL CONNECTIONS