ABB RELION REL670 manuals
RELION REL670
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Section 1 Introduction
- Product documentation
- Document revision history
- Related documents
- Document symbols and conventions
- Section 2 Safety information
- Caution signs
- Note signs
- Section 3 Environmental aspects
- Section 4 Unpacking, inspecting and storing
- Returning an IED damaged in transit
- Section 5 Mounting
- Flush mounting
- Mounting procedure for flush mounting
- panel rack mounting
- Mounting procedure for 19" panel rack mounting
- Wall mounting
- Mounting procedure for wall mounting
- Side-by-side 19" rack mounting
- Mounting procedure for side-by-side rack mounting
- Side-by-side flush mounting
- Mounting procedure for side-by-side flush mounting
- Mounting the coupling capacitor unit REX061 and shunt resistor unit REX062 (REG670 only)
- Shunt resistor unit REX062
- Making the electrical connection
- Front side connectors
- Rear side connectors
- Connection examples for high impedance differential protection
- Connecting to protective earth
- Connecting the power supply module
- Connecting the binary input and output signals
- Making the shield connection
- Making the electrical connection to the rotor and stator injection equipment (REG670 only)
- Coupling capacitor unit REX061
- Connecting injection unit REX060, coupling capacitor unit REX061 and shunt resistor unit REX062
- Connecting and setting voltage inputs
- Making of Ethernet connections
- Connecting remote communication interfaces LDCM
- Installing the serial communication cable for RS485
- Installing the serial communication cable for RS485 SPA/IEC
- Data on RS485 serial communication module cable
- Electrical installation
- Section 7 Checking installation
- Section 8 Removing, repairing and exchanging
- Sending the IED for repair
- Section 9 Technical data
- Case with rear cover
- Flush mounting dimensions
- Side-by-side flush mounting dimensions
- Wall mounting dimensions
- Section 10 Glossary
RELION REL670
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Section 1 Introduction
- Product documentation
- Document revision history
- Document symbols and conventions
- Document conventions
- Section 2 Safety information
- Caution signs
- Note signs
- Section 3 Environmental aspects
- Section 4 Unpacking, inspecting and storing
- Storing
- Section 5 Mounting
- Flush mounting
- Mounting procedure for flush mounting
- Mounting procedure for 19" panel rack mounting
- Wall mounting
- Side-by-side 19" rack mounting
- Mounting procedure for side-by-side rack mounting
- Side-by-side flush mounting
- Mounting procedure for side-by-side flush mounting
- Coupling capacitor unit REX061
- Shunt resistor unit REX062
- Section 6 Connecting
- Front side connectors
- Rear side connectors
- Connection examples for high impedance differential protection
- Connecting to protective ground
- Connecting to CT and VT circuits
- Connecting the binary input and output signals
- Making the shield connection
- Making the electrical connection to the rotor and stator injection equipment (REG670 only)
- Connecting injection unit REX060, coupling capacitor unit REX061 and shunt resistor unit REX062
- Connecting and setting voltage inputs
- Making of Ethernet connections
- Connecting remote communication interfaces LDCM
- Installing the serial communication cable for RS485
- Installing the serial communication cable for RS485 SPA/IEC
- Data on RS485 serial communication module cable
- Installing the GPS antenna
- Electrical installation
- Section 7 Checking installation
- Section 8 Removing, repairing and exchanging
- Exchanging the IED
- Section 9 Technical data
- Case with protective cover
- Flush mounting dimensions
- Side-by-side flush mounting dimensions
- Wall mounting dimensions
- Section 10 Glossary
RELION REL670
Table of contents
RELION REL670
Table of contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Table Of Contents
- Section 1 Introduction
- About the operator's manual
- Intended audience
- Revision notes
- Section 2 Safety information
- Section 3 Overview
- Section 4 Understand the local human-machine interface
- Key activated screens
- Medium
- Indication LEDs
- How to navigate
- Section 5 Understand the HMI tree
- Section 6 Read measured values
- View analog primary values
- View analog mean values
- View monitoring values
- View metering values
- Section 7 Event list
- Section 8 Handle disturbances
- View event recordings
- Section 9 Read and change settings
- TimeSynch
- General settings
- Remote communication
- Station communication
- Ethernet configuration
- Analog and I/O modules
- I/O modules
- Overview
- Control
- Control commands
- Monitoring
- Generic measured value MVGGIO
- Pulse counter logic PCGGIO
- Impedance protection
- Fullscheme distance protection, quadrilateral for earth faults ZMMPDIS, ZMMAPDIS (21)
- Directional impedance element for mho characteristics ZDMRDIR (21D)
- Power swing detection ZMRPSB (78)
- Directional over-power protection GOPPDOP (32)
- Pole discrepancy protection CCRPLD (52PD)
- Voltage protection
- Two step undervoltage protection UV2PTUV (27)
- Underfrequency protection SAPTUF (81)
- Phase segregated scheme communication logic for distance protection ZC1PPSCH (85)
- Local acceleration logic ZCLCPLAL
- Autorecloser SMBRREC (79)
- Logic
- Activate setting group
- Read internal events
- IED test mode
- Binary Input Module BIM
- Differential protection
- Secondary system protection
- Directional impedance ZDRDIR (21D)
- Directional under-power protection GUPPDUP (37)
- Sensitive directional residual over current and power protection SDEPSDE (67N)
- Two step overvoltage protection OV2PTOV (59)
- Rate-of-change frequency protection SAPFRC (81)
- Scheme communication
- Scheme communication logic for residual overcurrent protection ECPSCH (85)
- Commands
- Global positioning system
- Logic SR/RS memory
- Setting groups
- LED Test
- Section 12 Control and supervise the bay
- Locating and using the single line diagram
- Control screen messages
- Section 13 Reset
- Reset pulse counter PCGGIO
- All indication LEDs
- Section 14 Authorization
- Authorization handling in the IED
- Section 15 Glossary
RELION REL670
Table of contents
- Table Of Contents
- Application
- Available functions
- Differential protection
- Impedance protection
- Wide area measurement system
- Voltage protection
- Frequency protection
- Secondary system supervision
- Scheme communication
- Logic
- Monitoring
- Metering
- Basic IED functions
- Remote communication
- Hardware description
- Connection diagrams
- Technical data
- Ordering for customized IED
- Ordering for pre-configured IED
- Ordering for Accessories
Related products
RELION RER670RELION RET670Relion RES670Relion REG670Relion REC670RELION REB670RelionRelion 670 seriesRelion REB500RELION REM611ABB categories
Industrial Equipment
DC Drives
Controller
Relays
Measuring Instruments
Circuit breakers
Battery Charger
Industrial Electrical
Transformer
Switch
manualsdatabase
Your AI-powered manual search engine