Canon iR1018 Series Portable Manual

Also see for iR1018: Driver guide Service manual Brochure & specs Advanced operation guide Quick start guide

Contents

Chapter 383.2 Jam Code3.2.1 Jam Codes (Main body) 0013-1433/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /T-3-23.2.2 Jam Codes (ADF) 0013-1435/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /T-3-3E719 0000 Erroneous communication with card reader (serial communication)- Disconnection from the card reader has been detected sincecommunication started after confirmation of normalconnection to the card reader (after power-on).- A serial communication error has occurred. (The serialcommunication error cannot be recovered.)- Check the connectors of the card reader and image processorPCB.- Replace the card reader for normal connection.- Replace the image processor PCB.0001 Erroneous communication with coin vendor (serial communication)- Disconnection from the coin vendor has been detected sincecommunication started after confirmation of normalconnection to the coin vendor (after power-on).- A serial communication error has occurred. (The serialcommunication error cannot be recovered.)- Check the connection between the image processor PCB andserial PCB.- Check the connectors of the serial PCB and coin vendor fornormal connection.- Replace the serial PCB.- Check the coin vendor.- Replace the image processor PCB.E730 0000 inside error of the image processor PCB (PDL system error) - Replace the image processor PCB.The inside of the image processor PCB is faulty.E733 0000 Erroneous communication between controller and printerCannot communicate with the printer at startup. - Check the connectors of the DC controller PCB and imageprocessor PCB for normal connection.- Check the power supply of the printer (Check whetherinitialization is performed at startup).- Replace the DC controller PCB or image processor PCB.E736 0000 CCU communication errorThe installed modem PCB is incompatible. - Check the connectors of the image processor PCB and modem.- Replace the modem PCB.- Replace the image processor PCB.E739 0000 Erroneous communication between controller and network boardThe installed network board is incompatible. - Check the connectors of the image processor PCB and LANPCB for normal connection.- Replace the LAN PCB.- Replace the image processor PCB.E805 0000 Fan failureThe fan is faulty. - Check the fan connector.- Replace the fan.- Replace the DC controller PCB.E808 0000 Fixing drive circuit failure- The heater does not turn on.- A fixing drive motor failure was detected.- Check the connector of the fixing film unit.- Replace the fixing film unit.- Replace the fixing drive motor.- Replace the DC controller PCB.- Replace the power supply PCB.Code Name Sensor No. Description0104 Pickup Delay Jam SR11 After execution of a pickup retry, the registration sensor (SR11) does not detect the leading edge ofpaper within a specific period of time. Or after the duplex drive solenoid (SL1) is on, the registrationsensor (SR11) does not detect the leading edge of paper within a specific period of time.0208 Pickup Stationary Jam SR11 After the registration sensor (SR11) has detected the leading edge of paper, the registration sensor(SR11) does not detect the trailing edge of paper within a specific period of time.010c Delivery Sensor Delay Jam SR5 After the registration sensor (SR11) has detected the leading edge of paper, the delivery sensor(SR5) does not detect the leading edge of paper within a specific period of time.0210 Delivery Sensor StationaryJamSR5 - The delivery sensor cannot detect absence of paper within the specified time after turning off ofthe registration clutch.- The delivery sensor cannot detect absence of paper within the specified time after the sensordetected the leading edge of paper.0214 Stationary jam in machine SR5, SR9 After the registration sensor (SR11) has detected the trailing edge of paper, the delivery sensor(SR5) does not detect the trailing edge of paper within a specific period of time.021c Wound Paper Jam at Fuser SR5, SR11 The delivery sensor (SR5) has detected absence of paper within the prescribed time after it detectedpresence of paper.1118 Door open jam SR5, SR9, SR11,SW2The door was opened when there was printing paper in the transport path.Code Name Sensor No. Description0000 Unknown jam - Other errors0007 Initial stationary SR2002, SR2003, SR2004 Paper is detected in the transport path before the ADF starts initialoperation.DisplayCodeDetail Code Main Cause/Symptom Countermeasure