Canon iR1018 Series Portable Manual

Also see for iR1018: Driver guide Service manual Brochure & specs Advanced operation guide Quick start guide

Contents

Chapter 5315.1.4.6 <033: Vertical scan magnification correction> 0013-1360/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Correct the magnification of vertical scanning of a book. The larger the adjustment value, the more the image stretches in the vertical scanning direction.5.1.4.7 <034: Horizontal scan magnification correction> 0013-1361/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Correct the magnification of horizontal scanning of a book. The larger the adjustment value, the more the image stretches in the horizontal scanning direction.5.1.4.8 <035: - 036:Reader motor speed change> 0013-1362/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Though no market adjustment work needs to be carried out, enter factory defaults at image processor PCB replacement.5.1.4.9 <041: Vertical scan start position adjustment (when scanning on a document fed from ADF)> 0013-1363/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Adjust the position at which vertical scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the left-side margin of theimage becomes.5.1.4.10 <042: Horizontal scan start position adjustment (when scanning on a document fed from ADF)> 0013-1364/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Adjust the position at which horizontal scanning of a document fed from the ADF starts. The larger the adjustment value, the narrower the top margin of the imagebecomes.5.1.4.11 <043: Horizontal scan end position correction ((copy:scanning on ADF)> 0013-1365/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Adjust the position at which horizontal scanning of a document being copied ends (when scanning on a document fed from ADF). The larger the adjustment value,the narrower the bottom margin of the image becomes.5.1.4.12 <044: Horizontal scan end position correction (superfine:scanning on ADF)> 0013-1366/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Adjust the position at which horizontal scanning of a FAX document scanned in superfine mode ends. The larger the adjustment value, the narrower the bottommargin of the image becomes.5.1.4.13 <045: Horizontal scan end position correction (fine:scanning on ADF)> 0013-1367/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Adjust the position at which horizontal scanning of a FAX document scanned in fine mode ends. The larger the adjustment value, the narrower the bottom marginof the image becomes.5.1.4.14 <046: Horizontal scan end position correction (standard:scanning on ADF)> 0013-1369/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Adjust the position at which horizontal scanning of a FAX document set to the standard scan resolution ends. The larger the adjustment value, the narrower thebottom margin of the image becomes.5.1.4.15 <047: Vertical scan magnification correction (when scanning on a document fed from ADF)> 0013-1370/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Correct the magnification of vertical scanning of a document fed from the ADF. The larger the adjustment value, the more the image stretches in the vertical scan-ning direction.5.1.4.16 <048: Horizontal scan magnification correction (when scanning on a document fed from ADF)> 0013-1371/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Correct the magnification of horizontal scanning of a document fed from the ADF. The smaller the adjustment value, the more the image ruduces in the horizontalscanning direction.This menu is used to adjust the ADF feed motor speed. If you changed the adjustment value in this mode, the adjustment value selected for SCAN NUMERIC>54must also be incremented/decremented by the same amount.Do not change the adjustment value extremely.5.1.4.17 <054: Pickup motor speed correction (when the ADF is used) > 0013-1372/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /This menu is used to adjust the ADF pickup motor speed. If you have adjusted the ADF feed motor speed by selecting SCAN NUMERIC>48, the ADF pickupmotor speed must also be incremented/decremented by the same amount.Do not change the adjustment value extremely.5.1.4.18 <193: ADF special standard-sized paper: LGL misidentification-ready> 0013-1373/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /Set to use special standard-sized paper that is not otherwise identifiable to the ADF (because it is misidentified as "LEGAL").