manuals
database
Your AI-powered manual search engine
Search
Home
Brands
Carestream Helth
Medical Equipment
Kodak Point-of-Care CR 120
Carestream Helth Kodak Point-of-Care CR 120 Service Manual
Print this manual
Download
Carestream Helth Kodak Point-of-Care CR 120 Service Manual
Table of content
Contents
H4866
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Table Of Contents
Safety and Regulatory Information
Electrical Hazards
Labelling Summary
Device-specific Safety Information
System Description
Block Diagram of the Point-of-Care CR 120/140
Scanner Front View
Scanner Left View
Component Description
Motion Board
Sensor Board
Laser Board
Laser
Roller Motor
Linear Slide Assembly
Carriage Stepper Motor
Power Supply Assembly
Auto-loop Key Assembly and Tray Assembly
Erase Lamps
Erase Lamps Inverter Assembly
Erase Lamp Sensor
Left Limit Sensor
Screen Size Sensor
Roller Sensor
Z0 Sensor
Top WO Sensor
Service Procedures
Access to Cover Screws
Disconnecting the Laser
Replacing the Fuses
Power Inlet Module Replacement
Line Filter Wire Attached to Ground
USB Board Replacement
Motion Board Replacement
Sensor Board Replacement
PM Tube and PM Board Replacement
PM Assembly Screw (one side shown)
Laser Board Replacement
Laser Operation
Roller Motor Replacement
Roller Motor Drive retaining screw
Operating the Roller Motor
Linear Slide Assembly Replacement
Stepper Motor and Left Limit Sensor Connectors
Slide Assembly Attaching Screws
Linear Slide Test
Loader Stepper Motor Replacement
Bottom of Unit
Loader Assembly with Stepper Motor
Power Supply Assembly Replacement
Power Supply Screws on Unit Bottom
Connectors on the Motion Board
Main Ground Stud
Erase Lamps Assembly Replacement
W0 Upper Sensor Cable Connector
Erase Lamp Assembly Wiring Harness
Erase Lamps Inverters Replacement
Inverter Attaching Screws
Erase Lamps Sensors Replacement
Erase Lamp Sensor Screws
Left Limit Sensor Replacement
Linear Motor Section of Diagnostics Screen
Right Limit Sensor Replacement
Screen Size Sensor Replacement
Z0 Light
Roller Sensor Replacement
Z0 Sensor Replacement
W0 Sensors Replacement (Top/Receiver and Bottom/Transmitter)
W0 Top Sensor
W0 Bottom Sensor
Black Probe Attachment Point
Screen Guide Replacement for non Auto-loop systems
Remove the L Bracket
Pull the Key Assembly towards you
Install the New Screen Guide to the Key Assembly
Rotate the Rollers Manually
Auto-loop Key Assembly Replacement
Release the screws securing the Auto-loop Key Assembly
Pass the cable around to the Motion card (1)
Auto-loop Solenoid Replacement
Tray Assembly Replacement for non Auto-loop Systems
Remove J513 and J514 sensors
Remove the two screws retaining the black L-bracket
Pull out the Key assembly
Plate sides mounting screws
Tray Assembly Replacement for Auto-loop Systems
Remove the four screws retaining the Key assembly
Calibrations
New X and Y Coordinates
Insert Cassette Message
Position of the Dosimeter
Calibration Tab
Find PM Gain
Calibration Successful Screen
Facility Calibrations for Kodak QC Version 2.1.2/2.4.2 Software
Screen Image in the Image Viewer screen
Image Viewer Selections
Centered Histogram
Decrease PM Gain Value and Save
Increase PM Gain and Save
Image Appearing Four Way Split Screen in the Image Viewer
Save Cv Filter Setting Screen
Gain Tuning Calibration Process for Kodak QC Version 2.5
Set Image and Diagnostic settings
Save PM settings
Adjustments
Plastic gap jigs
Screen Guide Adjustment (non Auto-loop)
Loader Position
Loosen the L Bracket screws
Loader Pin and Loader Pusher Adjustments
Checking Pin Height (Go)
Diagnostics Screen -activate erase lamps
Roller Sensor Adjustment
Screen inserted between the rollers
Electric Schematic Diagrams
USB and Motion Schematics
Sensors Schematics
PM, Laser Schematics
Lamps Board Schematics
PS, Lamps Schematics
Grounding Schematics
Preventive Maintenance
User Tab
Removing the Protective Strips
Pull Out Cleaning Plate Message
Cleaning the Phosphor Screens
Installing the Extraction Tool
Releasing the Extraction Tool
Installing the Screen
Publication History
62
6H4866-02
Linear Slide Test
(b)
Click the left and right arrows to move the slide from side to side.
(c)
Check that the optical head moves smoothly and that the wires are not stuck during movement.
[7]
Assemble the Scanner Cover and Service Panel.
Previous
Next
/ 156
Zoom view
This manual is suitable for:
Kodak Point-of-Care CR 120
Kodak Point-of-Care CR 140
manuals
database
Your AI-powered manual search engine
