Denon AVR-2310CI Owner's Manual

Also see for AVR2310CI - Multi-Zone Home Theater Receiver: Specification Service manual Capabilites and Compatibilities Getting started guide Product sheet

2ENGLISHGetting Started Connections Playback Remote Control Information Troubleshooting SpecificationsMulti-ZoneMaking the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)This is displayed after the Audyssey Auto Setup procedure iscompleted.Even if the settings are changed after the Audyssey Auto Setupprocedure, the Audyssey Auto Setup settings can be restored byselecting “Restore” then pressing .1 Press ui to select“Parameter Check”,then press p or .2 Use ui to select the item you want to check, thenpress p or .Speaker Config. Check : Check the speaker configurationDistance Check : Check the distanceChannel Level Check : Check the channel levelCrossover Freq. Check : Check the crossover frequencyEQ Check : Check the equalizer3 Use o p to switch the display between the differentspeakers.4 Press .The confirmation screen reappears. Repeat steps 2 and 3.Check Audyssey Auto SetupMeasurement Results (Parameter Check)A U T O S E T U PP A R A M E T E R C H E C KS p e a k e r C o n f i g C h e c kD i s t a n c e C h e c kC h a n n e l L e v e l C h e c kC r o s s o v e r C h e c kE Q C h e c kR e s t o r eS h o w s p e a k e r c o n f i g u r a t i o n r e s u l tError messages (examples) Cause MeasuresA U T O S E T U PA U D Y S S E Y A U T O S E T U P M u l t E QC a u t i o n !N o m i c r o p h o n e o r S p e a k e rR e t r yR E T U R N C a n c e lC h e c k c a u s e o f p r o b l e m !• Included setup microphone is not connected.• Not all speakers could be detected.• The front L speaker was not properly detected.• Connect the included setup microphone to theSETUP MIC jack on the main unit.• Check the speaker connections.A U T O S E T U PA U D Y S S E Y A U T O S E T U P M u l t E QC a u t i o n !A m b i e n t n o i s e i s t o o h i g ho r L e v e l i s t o o l o wR e t r yR E T U R N C a n c e lC h e c k c a u s e o f p r o b l e m !• Too much noise in the room for accuratemeasurements to be made.• Speaker or subwoofer sound is too low foraccurate measurements to be made.• Either turn off any device generating noise ormove it away.• Try again when the surroundings are quieter.• Check the speaker installation and the directionin which the speakers are facing.• Adjust the subwoofer’s volume.A U T O S E T U PA U D Y S S E Y A U T O S E T U P M u l t E QC a u t i o n !F r o n t R N o n eR e t r yE N T E R E n t e r R E T U R N C a n c e lC h e c k c a u s e o f p r o b l e m !• Displayed speaker could not be detected.· The front R speaker were not properly detected.· Only one channel of the surround speakers wasdetected.· Sound was output from the R channel when onlyone surround back speaker was connected.· The surround back, but the surround speaker wasnot detected.• Check the connections of the displayedspeaker.A U T O S E T U PA U D Y S S E Y A U T O S E T U P M u l t E QC a u t i o n !F r o n t L P h a s eR e t r yS k i pE N T E R E n t e r R E T U R N C a n c e lC h e c k c a u s e o f p r o b l e m !• Displayed speaker connected with the polaritiesreversed.• Check the polarities of the displayed speaker.• For some speakers, this error message maybe displayed even if the speaker is properlyconnected. If you are sure that the wiring iscorrect, press ui to select “Skip”, then press.NOTE Be sure to turn the power off before checking the speaker connections.n To perform the Audyssey Auto Setup procedure againPress ui to select “Retry”, then press .n To cancel Audyssey Auto SetupPress , the “Cancel auto setup?” prompt is displayed.Press o p and select “�es”, then press .Error MessagesIf the Audyssey Auto Setup procedure could not be completed due to speaker installation, the measuring environment, etc., an error message isdisplayed. If this happens, check the relevant items, be sure to take the necessary measures, then perform the Audyssey Auto Setup procedureover again.Front: Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menuRemote controloperation buttons : Displaying the menuCancel the menuSettings