Denon AVR-2310CI Owner's Manual

Also see for AVR2310CI - Multi-Zone Home Theater Receiver: Specification Service manual Capabilites and Compatibilities Getting started guide Product sheet

29Getting Started Connections Playback Remote Control Information Troubleshooting SpecificationsENGLISHMulti-ZoneMaking detailed settings (Manual Setup)Setting items Setting contentsSpeaker Config.Select speaker configurationand size.(bass reproduction capability)“S.Back” is displayedwhen the “Amp Assign”setting (vpage 28) isset to “Normal”.“Front Height” isdisplayed when the “AmpAssign” setting (vpage28) is set to “FrontHeight”.NOTESelect “Large” or “Small” notaccording to the physical sizeof the speaker but accordingto the low frequencyreproduction capabilitiesbased on the frequency setat “Crossover Frequency”(vpage 30).Surround : Set the presence and size of the Surround speakers.Large : Use of a large speaker that can adequately play back lowfrequencies.Small : Use of a small speaker that has inadequate playback capacity forlow frequencies.None : Select when the surround speakers are not connected.“Large” is not displayed when “Front” is set to “Small”.•••S.Back : Set the presence, size and number of surround back speakers.Large : Use of a large speaker that can adequately play back lowfrequencies.Small : Use of a small speaker that has inadequate playback capacity forlow frequencies.None : Select when the surround back speakers are not connected.2sp : Use two surround back speakers.1sp : Use only one surround back speaker. Surround back audio is outputfrom the surround back L terminal.• “Large” is not displayed when “Surround” is set to “Small”.• Even if “S.Back” is set to “Large”, the “S.Back” setting is automaticallyswitched to “Small” if “Surround” is set to “Small”.NOTEEven when the Surround Back Speaker setting is other than “None”,sound may not be emitted from the surround back speaker, dependingon the playback source. In this case, “Surround Back” setting otherthan “OFF” (vpage 49).•••••Front Height : Set the front height speaker size.Large : Use of a large speaker that can adequately play back lowfrequencies.Small : Use of a small speaker that has inadequate playback capacity forlow frequencies.None : Select when a front height speaker is not connected.• “Large” is not displayed when “Front” is set to “Small”.• Even if “Front Height” is set to “Large”, the “Front Height” settingis automatically switched to “Small” if “Front” is set to “Small”.•••Setting items Setting contentsBass SettingMake the settings related toplayback of low frequencysignals (subwoofer and LFE).This can be set when“Speaker Config.” –“Subwoofer” (vpage28) is set to “�es”.Subwoofer Mode : Select low range signal to be reproduced bysubwoofer.LFE : Add the low frequency signal of the channel for which the speakersize is set to “Small” to the subwoofer signal and output it.LFE+Main : Add the low frequency signal of all channels to the subwoofersignal and output it.• Play music or a movie source and select the mode offering thestrongest bass.• Select “LFE+Main” if you want the bass signals to always beproduced from the subwoofer.••LPF for LFE : Set the upper limit of the low frequency signals output fromthe subwoofer.80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz•DistanceSet the distance from thelistening position to thespeakers.Measure the distance fromthe listening position to thespeakers beforehand.Unit : Set the unit of distance.FeetMeters••Step : Set the minimum variable width of the distance.1ft / 0.1ft0.1m / 0.01m••FL (Front L)/ FR (Front R)/ C (Center)/ SW (Subwoofer)/ SL (Surround L)/SR (Surround R/ SBL (Surr. Back L)/ SBR (Surr. Back R)/ FHL (Front Height L)/FHR (Front Height R) : Select the speaker you want to set, and set thedistance. Set the value that is closest to the measured distance.0.0ft ~ 60.0ft / 0.00m ~ 18.00m• The speakers that can be selected differ depending on the “Amp Assign”(vpage 28) and “Speaker Config.” (vpage 29) settings.• Default settings :Front/Center/Subwoofer/Front Height : 3.6 meters (12 feet)Surround/Surr. Back : 3.0 meters (10 feet)NOTESet the difference in the distance between the speakers to less than 6.0meters (20 feet). “Relocate Speaker” is displayed on the screen if aninappropriate distance is set.••Default : Reset all distance settings to factory default.Yes : Reset to the defaults.No : Do not reset to the defaults.••: Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menuRemote controloperation buttons : Displaying the menuCancel the menuSettings