Denon AVR-2310CI Owner's Manual

Also see for AVR2310CI - Multi-Zone Home Theater Receiver: Specification Service manual Capabilites and Compatibilities Getting started guide Product sheet

0Getting Started Connections Remote Control Information Troubleshooting SpecificationsENGLISH Multi-ZoneSettingsSetting items Setting contentsFront HeightSet whether or not to usethe front height channel.ON : Use the front height channel.OFF : Do not use the front height channel.This can also be set by pressing .Subwoofer ATTAttenuate subwoofer levelwhen using EXT. IN mode.ON : The input from the subwoofer channel is attenuated.OFF : The input from the subwoofer channel is not attenuated. Usually usein this mode.Set this to “ON” if the subwoofer channel level seems too high whenplaying audio signal.SubwooferTurn subwoofer output onand off.ON : The subwoofer is used.OFF : The subwoofer is not used.DefaultRestores all the surroundparameter settings to theirdefaults.Yes : Reset to the defaults.No : Do not reset to the defaults.Setting items Setting contentsTone ControlSets the tone control functionON and OFF.This can be set when“Dynamic EQ” (vpage51) is set to “OFF”.ON : Allow tone adjustment (treble, bass).OFF : Playback without tone adjustment.The tone cannot be adjusted when in the DIRECT mode.BassAdjusts the low frequencies.This can be set when“Tone Control” is set to“ON”.–6dB ~ +6dB (0dB)TrebleAdjusts the highfrequencies.This can be set when“Tone Control” is set to“ON”.–6dB ~ +6dB (0dB)Setting items Setting contentsMultEQCorrects the frequencyresponse of the differentspeakers.NOTE• “MultEQ” and “ManualEQ” settings for which“Not Used” has been set at“EQ Customize” (vpage32) cannot be selected.• When using headphones,“MultEQ” is set to “OFF”.Audyssey : Optimize frequency response of all speakers.Audyssey Byp.L/R : Optimize frequency response of speakers exceptfront L and R speakers.Audyssey Flat : Optimize frequency response of all speakers to flatresponse.Manual : Apply frequency response set with “Manual EQ” (vpage 51).OFF : The “MultEQ” equalizer cannot be used.• When “Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” isselected, “ ” lights.• After running Audyssey Auto Setup, if the Speaker Configuration,Distance, Channel Level, and Crossover Frequency have changedwithout increasing the number of speakers measured, only “ ”lights.• This can also be set by pressing .• When the “Audyssey Auto Setup” (vpage 23) procedure is performed, the “MultEQ”, “DynamicEQ” and “Dynamic Volume” functions are enabled.• Operating conditions for each function• Dynamic EQ :When “MultEQ” is set to “ON”• Dynamic Volume :When “Dynamic EQ” is set to “ON”• Setting :When “Dynamic Volume” is set to “ON”NOTEIf the speaker settings are changed after the “Audyssey Auto Setup” procedure is performed,“MultEQ”, “Dynamic EQ” and “Dynamic Volume” functions cannot be selected and “Run Audyssey”is displayed.If this happens, either perform the “Audyssey Auto Setup” procedure again, or perform the “Restore”operation (vpage 27) to restore the settings to as they were after the “Audyssey Auto Setup”procedure was performed.MultEQDynamic EQDynamic VolumeSetting: Moves the cursor (Up/Down/Left/Right) : Decision the setting : Return to previous menuRemote controloperation buttons : Displaying the menuCancel the menuPlaybackAdjusting the Sound and Picture Quality (Audio/Video Adjust)Making the MultEQ, Dynamic EQ and Dynamic VolumeSettings (Audyssey Settings) Default settings are underlined.Adjusting the Tone (Tone Control)Default settings are underlined.