Denon AVR-3806 Operating Instructions Manual

Also see for AVR-3806: Operating instructions Capabilities and Compatibilities Guide Specifications Supplementary guide Code List

Contents

52Advanced OperationAdvanced OperationSetting the back light’s lighting time1 Press and hole the SET UP button for at leastthree seconds.• The IR segment blinks twice.2 Press the 9, 7, 8 button (9→→77→→88)) to select asetting.• The IR segment blinks twice.1 Press and hold the SETUP button for at leastthree seconds.• The IR segment blinks twice.2 Press the 9, 7, 3 button (9 →→ 7 →→ 3) to selectLight setup.• The IR segment blinks twice.3 Press the NUMBER button (1 to 5) you want toadjust the lighting time (5 sec ~ 25 sec).22 Lighting time1 : 5 sec2 : 10 sec (factory default)3 : 15 sec4 : 20 sec5 : 25 sec• The IR segment blinks twice as confirmation.1 Press and hole the SET UP button for at leastthree seconds.• The IR segment blinks twice.2 Press the 9, 7, 8 button (9→→77→→88)) to select asetting.• The IR segment blinks twice.1 Press and hold the SETUP button for at leastthree seconds.• The IR segment blinks twice.2 Press the 9, 7, 9 button (9 →→ 7 →→ 9).• The IR segment blinks twice.Setting the ambient light sensorThe included remote control unit (RC-1024) has the ambient lightsensor which allows the EL display brightness to automaticallyadjust depending on how light or dark the amount ofincandescent light in the room is. Default state of the ambientlight sensor is “OFF” (disable).3 Press the ON button.• The IR segment blinks two or four times.Two blinks indicates that ambient light feature was disabled,and is now enabled. Four blinks indicates that ambient lightfeature was enabled, and is now disabled.• If you want to set the brightness of the display manually, set to“OFF” (default).Punch throughButtons used in the CD, DVD, and VCR modes can be assignedto the buttons which are not normally used in the TV andSAT/CBL modes.For example, when the DVD mode is set to the punch throughmode in the TV mode, the DVD mode’s PLAY (1), STOP (2),MANUAL SEARCH (6, 7), AUTO SEARCH (8, 9)and PAUSE (3) button’s signals are sent in the TV mode. — ( )1 Press and hole the SET UP button for at leastthree seconds.• The IR segment blinks twice.2 Press the 9, 7, 8 button (9→→77→→88)) to select asetting.• The IR segment blinks twice.1 Press and hold the SETUP button for at leastthree seconds.• The IR segment blinks twice.2 Press the 9, 8, 4 button (9 →→ 8 →→ 4) to selectpunch through setting.• The IR segment blinks twice.3 Select the MODE SELECTOR button (CD, DVD orVCR) you want to punch through.4 Press the button you want to punch through (1,2, 6, 7, 8, 9 or 3).5 Repeat step 4.6 Press the MODE SELECTOR button (TV orSAT/CBL) for which you want to set the punchthrough.7 Press and hold the SETUP button for at leastthree seconds.• The IR segment blinks twice.Setting the brightness• The brightness of the display can be adjusted in 5 levels.• The default brightness setting is level3 (level 5 = brightest).1 Press and hold the SETUP button for at leastthree seconds.• The IR segment blinks twice.3 Press and hold the SETUP button to exitprograming.• The IR segment twice as confirmation.2-1For 1 brightness step increase:Press the CHANNEL + button.2-2For 1 brightness step decrease:Press the CHANNEL – button.ENGLISHENGLISH