Denon AVR 4308CI - AV Network Receiver Owner's Manual

Also see for AVR 4308CI - AV Network Receiver: User manual Specifications Specification Owner's manual Manual

Contents

Denon AVR 4308CI - AV Network Receiver Owner's Manual Manual pdf 70 page image

Getting Started Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting SpecificationsMODESELECTORRemote IDAMP(MAIN)TUNERiPodNET/DTUDEVICE1(AnalogTUNER)DEVICE2(XM)DEVICE1(NetAudio)DEVICE2(HDRadio)1(Default) 81001 52863 52864 72815 62865 628402 82001 52795 52812 72816 62837 628413 83001 52800 52813 72817 62838 628424 84001 52805 52814 72818 62839 62843Setting the Remote IDWhen using multiple DENON AV receivers in the sameroom, make this setting so that only the desired AV receiveroperates.1 Press [AMP] to set the main remote control unit to theAMP mode.2 Press and hold in [RC SETUP] for at least 3 seconds.The signal transmission indicator flashes twice.3 Refer to the table at the right, and use [NUMBER] toinput the 5-digit number corresponding to the remoteID to be changed.The signal transmission indicator flashes twice.4 Press [TU], [iPod] or [NET/DTU] to select the mode tobe set.5 Repeat steps 2 to 4 to set the remote IDs for allmodes.NOTE• When changing a setting, be sure to set the same remote ID as theAVR-4308CI’s (vpage 38).• When changing the AMP mode’s remote ID, also change the“TUNER”, “iPod” and “NET/DTU” remote ID at the same time.• Set the remote ID of an analog tuner for “TUNER” – “DEVICE1”, theXM remote ID for “DEVICE2”.5 Point the main remote control units directly at eachother and press and hold the button on the otherdevice’s remote control unit that you want to learn.Once learning is completed normally, the display lights and thesignal transmission indicator flashes twice.b If you want to learn other buttons, repeat steps 4 and 5.b The mode can be switched by pressing [MODE SELECTOR].b The signal transmission indicator lights once for a long time iflearning was not possible6 Press and hold in [RC SETUP] for at least 3 seconds.The signal transmission indicator flashes twice and the settingis completed.Other device’sremote control unitAVR-4308CI’s main remotecontrol unit (RC-1068)Learning FunctionIf your AV devices are of a brand other than DENON or ifthey cannot be operated with the preset memory function,their remote control signals can be transfered to stored inthe AVR-4308CI’s main remote control unit.1 Press [MODE SELECTOR] for the device you want toset.2 Press and hold in [RC SETUP] for at least 3 seconds.The signal transmission indicator flashes twice.3 Press [9], [7] and [5], in that order.The signal transmission indicator flashes twice and the learningmode is set.4 Press the button to be set.The main remote control unit’s display turns off.b If a button that cannot be learned is pressed, the signal transmissionindicator lights but the signal is not learned.• With some remote control units, the signals cannot be learned or thedevice will not operate properly even when the signals have beenlearned. In this case, use the device’s own remote control unit.• Learned buttons have priority over the preset memory. If you nolonger need the learned setting, reset the learning function (vpage69).NOTE• [HOME] cannot be learned.• Do not learn any remote control signals at [RC SETUP].• The AMP, ZONE2, ZONE3, ZONE4 and SYSTEM CALL modes cannotbe learned.Remote Control[NUMBER][RC SETUP][SYSTEM CALL][ AMP][POWER ON][MODE SELECTOR][ NET/DTU][ TU][ iPod][ TV][8], [9],[1],[6], [7],[3], [2]Signaltransmissionindicator