Eaton Champ MLLA M2 Series Installation & Maintenance Information

Champ® MLLA M2 Series Linear Emergency LEDLuminaire Fittings for Hazardous LocationsInstallation & Maintenance InformationSAVE THESE INSTRUCTIONS FOR FUTURE REFERENCEIF 1946IF 1946 • 09/22 Copyright © 2022, Eaton’s Crouse-Hinds Division Page 1APPLICATIONCHAMP Linear Emergency LED luminaire are suitable for use in the followinghazardous (classified) locations as defined by the National Electrical Code(NEC®):The assembled luminaire shall be installed in accordance with the NationalElectric Code NFPA70, and American Bureau of Shipping.NEC• Class I, Division 2, Groups A, B, C, D• Class I, Zone 2• Class II, Division 1, Groups E, F, G• Class III• Wet location, IP66/67, Type 4XThese luminaire housings shall be used with UL listed Crouse-Hinds hazard-ous locations luminaire fittings namely LED Light Engine Cat Nos. MLLA*2 orMLLA*4 series ending with M2 and Mounting means Cat Nos. M2-FLUSH-MT-KIT, M2-CEILING-SWIVEL-KIT, M2-CEILING-WALL-KIT, M2-PM-KIT-1.25,M2-PM-KIT-1.5, M2-PM-KIT-2.0, (refer to label provided inside the driver housingfor permissible fitting details).UL Standards:• UL844 Hazardous (Classified)• UL1598 Luminaires, UL1598A Marine• UL8750• UL924CSA Standard:• CSA C22.2 No. 250• CSA C22.2 No. No.137• CSA C22.2 No. No.141Refer to the luminaire fitting nameplate for specific classification information,maximum ambient temperature suitability, and corresponding operatingtemperature (T-code).The assembled linear LED luminaire is designed for use indoors and outdoorsin marine and wet locations, where moisture, dirt, corrosion, vibration andrough usage may be present.INPUT VOLTAGE:• UNV1: 120-277 VAC 50/60 Hz1. Read carefully before installing and wiring luminaire and retain for futurereference.2. Ensure area to be free of hazardous atmospheres before and duringinstallation and maintenance.3. Do not use accessory equipment not recommended by manufacturermay cause an unsafe condition.4. Use only replacement parts from Eaton’s Crouse Hinds division.5. To avoid the risk of fire, explosion or electric shock, this product shouldbe installed, inspected and maintained by a qualified electrician only, inaccordance with all applicable electrical codes.6. Do not use this equipment for other than intended use.7. Replace entire battery unit and LED driver when necessary. Contact themanufacturer for information on service.8. Do not attempt to service battery.9. See product label for minimum supply wire temperature rating.10. Battery requires 24hrs to fully charge. Allow 24 hours charging timebefore depending on the battery to operate at full capacity.11. The emergency battery requires a minimum charge time of one (1) hourbefore testing the circuit, 24 hours is required for a full charge.12. Equipment should be mounted in locations and at heights where it willnot readily be subjected to tampering by unauthorized personnel. Max.mounting height: 25.2 feet)13. The emergency luminaire is intended to be installed with CG-256 (issuedby the American Bureau of Shipping and Coast Guard.14. This product must be installed in accordance with the applicable installa-tion code by a person familiar with the construction and operation of theproduct and the hazards involved.IMPORTANT SAFEGUARDS - READ AND FOLLOW ALL SAFETY INSTRUCTIONSSTORAGE INSTRUCTIONS1. EM luminaire must be stored in an ambient temperature range of 0°Cto 40°C.2. Battery should be charged and discharged within 6 months. At aminimum, the battery should be recharged within this time.WARNINGTo avoid electric shock:Be certain electrical power is OFF before and during installation andmaintenance.Luminaire must be supplied by a wiring system with an equipmentgrounding conductor in accordance to the NEC and CEC for the specificHazardous Locations involved.To avoid burning hands:Make sure lens and housing are cool when performing maintenance.! WARNINGTo avoid explosion:Make sure the supply voltage is the same as the luminaire voltage.Do not install where the marked operating temperatures exceed theignition temperature of the hazardous atmosphere.Do not operate in ambient temperatures above those indicated on theluminaire nameplate.Use proper supply wiring as specified on the luminaire nameplate.All gasket seals must be clean and undamaged.Before opening, electrical power to the luminaire must be turned off.Keep tightly closed when in operation.To reduce the risk of ignition due to electrostatic discharge, avoid contactwith the luminaire while explosive atmosphere is present. Clean only withdamp cloth.!