Eaton IQ 250 User & Installation Manual

Also see for IQ 250: User & installation manual Quick start guide

Contents

A IQ 250/260 Meter Appendix B:Modbus MappingFirst Overlay write only in PS update mode80E8 - 80E8 33001 - 33001 Input#1 - 2 bindings & logging enables UINT16 bit-mapped -------- 2222 1111 One nibble for each input.Assuming "abcd" as the bits in each nibble:"a": select this input for EOI (End Of Interval)pulse sensing."b": log this input when pulse is detected"cc": Input event trigger mode - Contact sensing method;00 = none; 01 = open to close; 10 = close to open; 11 = anychange.180E9 - 80E9 33002 - 33002 Relay #1 Delay to Operate UINT16 0.1 second units Delay to operate the relay since request. 180EA - 80EA 33003 - 33003 Relay #1 Delay to Release UINT16 0.1 second units Delay to release the relay since request. 180EB - 80F0 33004 - 33009 Reserved UINT16 Set to 0. 680F1 - 80F1 33010 - 33010 Relay #2 Delay to Operate UINT16 0.1 second units Delay to operate the relay since request. 180F2 - 80F2 33011 - 33011 Relay #2 Delay to Release UINT16 0.1 second units Delay to release the relay since request. 180F3 - 8108 33012 - 33033 Reserved UINT16 Set to 0. 228109 - 8109 33034 - 33034 Input Accumulators Scaling UINT16 bit-mapped -------- 22221111 1810A - 810A 33035 - 33035 Relay Accumulators Scaling UINT16 bit-mapped -------- 22221111 1810B - 8126 33036 - 33063 Reserved Set to 0. 28Block Size: 63First Overlay write only in PS update mode80E8 - 80E8 33001 - 33001 Input#1 - 4 bindings & logging enables UINT16 bit-mapped 44443333 22221111 One nibble for each of the 4 inputs.Assuming "-bcc" as the bits in each nibble:"b": Log this input when pulse is detected"cc": Input event trigger mode - Contact sensing method;00 = none; 01 = open to close; 10 = close to open; 11 = anychange.180E9 - 80E9 33002 - 33002 Source for Pulse Ouput#1 UINT16 enumeration -----ppp ----vvvv " ppp" (Phase) : 000 = none, 001 = Phase A, 010 = PhaseB, 011 = Phase C, 100 = All Phases, 101 = Pulse fromEOI(End Of Interval)."vvvv"(Value) :0000= none,0001 = Wh,0010 = +Wh,0011 = -Wh,0100= Varh,0101 = +Varh,0110 = -Varh,0111 = VAh,1000= Received Wh,1001= Delivered Wh,1010= Inductive Varh,1011 = Capacitive Varh180EA - 80EA 33003 - 33003 Kt [Wh/pulse] factor for Pulse Output#1 UINT16 bit-mapped ddVVVVVV VVVVVVVV "V…V" = not scaled energy value per pulse, from 0 to9999."dd"= decimal point position: 00=0.XXXX, 01=X.XXX,10=XX.XX, 11= X.XXX.180EB - 80EC 33004 - 33005 Output#2 Assignment and Kt UINT16 280ED - 80EE 33006 - 33007 Output#3 Assignment and Kt UINT16 2* 4 bits per accumulator* 0xF disables the accumulation* 0-5 = power of divisor for the scaled accumulatorExample: count=12456, 4bits=3:divisor=103=1000 & scaled accumulator=12.Settings Registers for Digital I/O Pulse Output CardSame as Output #1.Settings Registers for Digital I/O Relay CardSame as Output #1.www.eaton.com IB02601006E MM-22