Genie SilentMax 1000 Operation & Maintenance Manual

Also see for IntelliG 1000: Manual Product guide Operation and maintenance manual Operation & maintenance manual Operation & maintenance manual

Contents

Genie SilentMax 1000 Operation & Maintenance Manual Manual pdf 8 page image

7 ©2011 The Genie Company 9/2011IntelliCode® 1 or 2 wireless keypadDoor moves.(To verify memory is cleared—try to operate the garage doorusing one of your remote devices. The opener shouldnot respond.)Both LEDs OFF confirms communicationis established with operator.Round LED BLUE then OFF, Long LED FLASHINGPROGRAMSETPress & hold2 seconds.Release.ACTION LED INDICATION/RESULTBLUEOFFOFFOFFOFFOFFBOTH BLUEFLASHINGRelease.OFFPURPLEFLASHINGClearing remotes from powerhead memory willclear ALL programmed remotes and wirelesskeypad.NOTE:All remotes and wireless keypadsmust be reprogrammed.Your door opener will no longer recognize anysignal received from a missing remote.Press & holdBOTH openand closebuttonstogether.REMOTE CLEARED FOR REPROGRAMMINGLOST OR STOLEN REMOTE - CLEARING MEMORYOPTIONAL PROGRAMMING123Enter your PINon the wireless keypad.OFF BLUE OFFPress & release 2 times.Press &releaseACTION LED INDICATION/RESULTGenie® Intellicode® 2 Wireless Keypad comeswith a complete set of instructions.Independent Light Control ButtonControls door opener lights from inside garageSure-Lock™ ButtonretfaslortnocselbasidKCOL–.desolcyletelpmocsirood– UNLOCK allows controls towork normallyIndicator LightRed indicator light is always ONWhen Sure-Lock™ is ON theindicator light flashesOpen/Close ButtonOpen and closes door from inside garage.WALL CONSOLE - OVERVIEWUse only the Series III wall console provided with this unit.Wall console has three buttons and one indicator light.Indicator LightIndicator light will display Red when wall console isproperly wired and Sure-Lock™ is OFF. When Sureis ON indica Lock™tor light flashes.Open/Close ButtonUse this button to open or close garage door. WhenSure-Lock™ is ON the Open/Close button will CLOSEdoor only. Note: Constant button pressure in theCLOSE mode will override error responses in thepowerhead and close door.Independent Light Control ButtonUse this button to turn powerhead lights ON.Powerhead lighting will remain ON until this buttonis pressed again or a door action has been completed.Note: If opener has a Motion Detector sensor, it willkeep powerhead lights ON as long as motion is detectedSure-Lock™ ButtonWhen Sure-Lock™ is ON the powerhead cannot beactivated by the wall console or a remote.s Press and hold for 5 seconds (or until IndicatorLight flashes) to activate Sure-Lock™.s Press and release to turn Sure-Lock™ OFF.Tip: If the Wall Console is energized (LED ON), but thedoor does notrespond to theOPEN/CLOSEbutton-verifythe Console iswired to theBWC terminalson the powerhead. STB BWC IWCNOTUSED NOTUSEDNOTUSED NOTUSEDFROM STBsFROM WALLCONSOLESTB BWC IWCFROM STBsFROM WALLThis opener has a Serial Number sticker in which the serialnumbers begin with 10 or higher.MODEL AC SR3 THE GENIE COMPANYFCC ID: B8Q AC SR3 Residential Door OperatorIC: 2133A-CSD1D 120V. 60HZ. 5AFOR H LP CAL 1-800-35GENIE OR WWW.GENIECOMPANY.COMS/N:10XXXX XXXXXXXWall consoles from other manufacturers may not work withopeners of these serial number groups. Genie® Series I wallbuttons and Series II wall consoles will not work with openersof this serial number group.ROGRAMSETPress & Hold for2 seconds or untilround LED turns bluethen OFF.Then Long LED flashes purple.1245PURPLEFLASHINGCONSOLE