Installing an optional ServeRAID adapter advanced feature key . . . . . 205Removing a ServeRAID SAS controller battery from the remote battery tray 207Installing a ServeRAID SAS controller battery on the remote battery tray 208Removing a hot-swap hard disk drive . . . . . . . . . . . . . . . 210Installing a hot-swap hard disk drive . . . . . . . . . . . . . . . 210Removing a simple-swap hard disk drive . . . . . . . . . . . . . . 211Installing a simple-swap hard disk drive . . . . . . . . . . . . . . 212Removing an optional CD-RW/DVD drive. . . . . . . . . . . . . . 213Installing an optional CD-RW/DVD drive . . . . . . . . . . . . . . 214Removing a tape drive . . . . . . . . . . . . . . . . . . . . 214Installing a tape drive . . . . . . . . . . . . . . . . . . . . . 216Removing a memory module (DIMM) . . . . . . . . . . . . . . . 217Installing a memory module . . . . . . . . . . . . . . . . . . . 217Installing a DIMM . . . . . . . . . . . . . . . . . . . . . . 222Removing a hot-swap fan . . . . . . . . . . . . . . . . . . . 223Installing a hot-swap fan . . . . . . . . . . . . . . . . . . . . 224Removing a hot-swap ac power supply . . . . . . . . . . . . . . 225Installing a hot-swap ac power supply . . . . . . . . . . . . . . . 226Removing the battery . . . . . . . . . . . . . . . . . . . . . 229Installing the battery . . . . . . . . . . . . . . . . . . . . . 231Removing the operator information panel assembly . . . . . . . . . . 233Installing the operator information panel assembly . . . . . . . . . . 233Removing and replacing Tier 2 CRUs . . . . . . . . . . . . . . . . 234Removing the bezel . . . . . . . . . . . . . . . . . . . . . 234Installing the bezel . . . . . . . . . . . . . . . . . . . . . . 234Removing the SAS hard disk drive backplane . . . . . . . . . . . . 235Installing the SAS hard disk drive backplane . . . . . . . . . . . . 235Removing the simple-swap hard disk drive backplate . . . . . . . . . 236Installing the simple-swap hard disk drive backplate . . . . . . . . . . 237Removing and replacing FRUs . . . . . . . . . . . . . . . . . . 238Removing a microprocessor and heat sink . . . . . . . . . . . . . 238Installing a microprocessor and heat sink . . . . . . . . . . . . . . 240Thermal grease . . . . . . . . . . . . . . . . . . . . . . . 244Removing a heat-sink retention module . . . . . . . . . . . . . . 246Installing a heat-sink retention module . . . . . . . . . . . . . . . 246Removing the system board . . . . . . . . . . . . . . . . . . 247Installing the system board . . . . . . . . . . . . . . . . . . . 248Removing the 240 VA safety cover . . . . . . . . . . . . . . . . 250Installing the 240 VA safety cover . . . . . . . . . . . . . . . . 251Chapter 6. Configuration information and instructions . . . . . . . . 253Updating the firmware . . . . . . . . . . . . . . . . . . . . . . 253Configuring the server . . . . . . . . . . . . . . . . . . . . . . 253Using the Setup utility . . . . . . . . . . . . . . . . . . . . . 255Using the Boot Selection Menu program . . . . . . . . . . . . . . 260Starting the backup server firmware . . . . . . . . . . . . . . . . 260Using the ServerGuide Setup and Installation CD. . . . . . . . . . . 260Using the integrated management module . . . . . . . . . . . . . 263Using the USB memory key for VMware hypervisor . . . . . . . . . . 264Using the remote presence capability and blue-screen capture . . . . . . 265Using the embedded hypervisor . . . . . . . . . . . . . . . . . 266Enabling the Broadcom Gigabit Ethernet Utility program . . . . . . . . 267Configuring the Gigabit Ethernet controller . . . . . . . . . . . . . 267Using the LSI Configuration Utility program . . . . . . . . . . . . . 268IBM Advanced Settings Utility program. . . . . . . . . . . . . . . 270Updating IBM Systems Director . . . . . . . . . . . . . . . . . . 270Contents v
