Kenwood KRF-X9070D Instruction Manual

Also see for KRF-X9070D: Service manual Instruction manual Instruction manual

Contents

Kenwood KRF-X9070D Instruction Manual Manual pdf 23 page image

23 ENPreparing for surround soundSpeaker settingsTo enable you to obtain optimum enjoyment from the receiver’s listeningmodes, make sure to complete the speaker settings (subwoofer, front,center, and surround speakers) as described below.PTYSETUP MULTI CONTROLRCVR PWRSETUPMULTITUNERPOWERON/STANDBY(VR-7080)ON/STANDBY(KRF-X9070D)POWER ON/OFF(KRF-X9070D)%/fi/@/#SOUNDSOUND1Turn on the power to this receiver by pressing the POWERON/STANDBY key or RCVR PWR key.• When you use the remote control, press the SUB key to switchto sub screen mode.2Press the SETUP key to enter the SETUP mode.The Surround Back and Subwoofer speaker output selections aredisplayed as follows:1 6ch AMP SB : Surround Back/Subwoofer speaker terminalwill output SB sound. Surround Back pre outwill have output from SBL only.2 6ch AMP SW : Surround Back/Subwoofer speaker terminalwill output SW sound. Surround Back preout will have output from SBL and SBR.3 6ch AMP OFF : It is not advisable to use Surround Back/Subwoofer speaker terminal for thisselection.Use the MULTI CONTROL knob or MULTI %/fi keys to select thespeakers.Press the SETUP key to proceed to the next SETUP selection.Use ∧∧∧∧∧/∨∨∨∨∨keys or MULTI @/ # keysfor the following displays.1 SP SETUP2 TEST TONE3 BASS PEAK4 SP DISTANCE5 DISP MODE6 EXITThe flow of the SETUP is as follows:3Select a speaker system.If you have THX certified speakers, please set them to NML/THX.1 Select the SP SETUP and press the SETUP key again so thatthe subwoofer setting indication “SUBW ON” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE2 Use the MULTI CONTROL knob or MULTI %/fi keys to selectthe appropriate subwoofer setting.1 SUBW ON : Subwoofer setting mode to the receiver is ON.2 SUBW OFF : Subwoofer setting mode to the receiver is OFF.• The initial setting is “SUBW ON”.• When the setting “SUBW OFF” is selected, the front speakersare automatically set to “FRNT LARGE” and the procedure skipsto step 6.Before step 6, press the SETUP key to accept the setting.• When subwoofer output sound is required, select “FRNT NML/THX”, or select both “FRNT LARGE” and “SW RE-MIX ON”.• After setting SW (subwoofer) from OFF to ON, 6ch AMP setupdisplay will appear to enable you to re-select either SW, SB or OFFfrom the surround back or subwoofer speaker terminal.3 Press the ∧∧∧∧∧ key or MULTI # key to accept the setting.• The front speakers setting indication “FRNT” appears.LSL S SB SRC RSP MUTE OPTICAL 6CH INPUTCOAXIAL ANALOG 96kHzfsCINEMA EQ.ACTIVE EQ.DSP MODEDTS.MATRIXDISCRETEDOLBY DIGITALPRO LOGICSTEREOLOUDNESSNEO:6CSIIA B CLIPAUTO DETECT THXAUTORDSRTYMEMOSTEREOTUNEDSurround EXSWLFE4 Use the MULTI CONTROL knob or MULTI %/fi keys to selectthe appropriate front speakers setting.1 FRNT LARGE : Large front speakers are connectedto the receiver.2 FRNT NML/THX : Average size front speakers areconnected to the receiver.• For “FRNT LARGE” selection, no sound will be heard fromsubwoofer speaker even when it is set to on. However, if youselect “SW RE-MIX ON” when subwoofer is selected, you willbe able to hear sound from the subwoofer.When in STEREO mode, the sound goes directly to frontspeaker.5 Press the ∧∧∧∧∧ key or MULTI # key to accept the setting.• The center speaker setting indication “CNTR” appears.Continued to next pageSP SETUP TEST TONE BASS PEAK SP DISTANCE EXITDISP MODEFront LeftCenterFront RightSurround RightSurround Back(Surround BackRight/Left)Surround LeftSubwooferDisplay SelectorDisplay ListenSubwooferFrontCenterSurroundSurroundBackSurroundMixSubwooferRe-mixT. TONEMANUALT. TONEAUTOLCRSRSLSB(SBR/SBL)SWLCRSRSB(SBR/SBL)SLSW