Kenwood TK-5710 Service Manual

Also see for TK-5710(H): Instruction manual Specifications Instruction manual Instruction manual Instruction manual

8TK-5710(B)/5710H(B)No. Setup item Display Remarks1 Select Zone/Channel ∗ ∗ - ∗ ∗ ∗ Zone : 1~50, Channel : 1~2502 RX Frequency 1 ∗ ∗ . ∗ ∗ ∗ ∗ ∗ MHz Receive frequency3 TX Frequency 1 ∗ ∗ . ∗ ∗ ∗ ∗ ∗ MHz Transmit frequency4 Channel Type TYPE ANALOG/APCO/MIXED5 TX Mode MODE ANALOG/APCO6 Channel Spacing SPACE 25.0kHz/12.5kHz (When the Channel type is selected "ANALOG" or "MIXED".)APCO 12.5kHz/12.5kHz (When the Channel type is selected "APCO".)7 RX Signaling RX-SIG Receive QT/DQT8 TX Signaling TX-SIG Transmit QT/DQT9 RX NAC RX-NAC ∗ ∗ ∗ 000~FFF (Hexadecimal) Note:"F7F" cannot be set.10 TX NAC TX-NAC ∗ ∗ ∗ 000~FFF (Hexadecimal) Note:"F7E" and "F7F"cannot be set.11 Talkgroup List No. None When you do not want to set the Talkgroup list number to the transceiver.∗ ∗ ∗ Talkgroup list number (1~250)(When the Talkgroup list name is not set to the transceiver.)∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗ Talkgroup list name (12 digits)(When the Talkgroup list name is set to the transceiver.)The setup items for self programming mode are as follows.9. Self Programming ModeWrite mode for frequency data and signaling etc. To beused ONLY by the authorized service person maintaining theuser's equipment. After programming, reset the FPU to the"Self- Programming" disabled mode. Transceivers CANNOTbe delivered to the end-user in the self-programming mode.The following setup items in the channels programmed bythe FPU can be changed using the self-programming mode.The addition of new channel and the deletion of channel thathas already been programmed by the FPU cannot beperformed using the self-programming mode.• RX Frequency• TX Frequency• Channel Type• TX Mode (When the channel type is selected "MIXED".)• Channel Spacing• RX Signaling• TX Signaling• RX NAC• TX NAC• Talkgroup List No.Note:The personality will be also changed when the above-mentioned items is changed. (Refer to the FPU for thepersonality details.)9-1. Enter to the self programming modePress and hold the [GRP^] key while turning the trans-ceiver power ON. Ignoring whether the Read authorizationpassword is set or not, "PASSWORD" appears.If the Read authorization password is not set to the trans-ceiver, "SELF PG MODE" is displayed on the LCD when the[PF2] key is pressed while "PASSWORD" is displayed.If the password is set to the transceiver, "SELF PG MODE"is displayed on the LCD when you enter the correct pass-word while "PASSWORD" is displayed.For the password input method, see "8. Clone Mode”step 3 described on page 7.Note :This mode (self programming mode) cannot be set whenit has been disabled with the FPU.9-2. Data writingIf the [PF4] key is pressed while Zone/Channel mode isdisplayed, new data is written into memory. "WRITING" isdisplayed while the transceiver is writing data.REALIGNMENT