21Operation$ Setting the video signalsIn the multi-function controller, the video signals (compositesignals and component signals) which will be used must beset.The correct video signals cannot be obtained unless thesesettings are performed.1. Select the pan-tilt head system using theCONTROL/PREVIEW MONITOR OUT SEL button.2. Press the MENU button, turn the menu setting control(main), and set it so that the CONTROLLER SETTINGitem appears at the top of the LCD panel.3. Press the OK button.The following item appears on the LCD panel.This menu shows that input sinal is composite signal andoutput signal is composite signal.4. Turn the menu setting control (L), and set the video inputsignals (displayed at the bottom left on the LCD panel).Composite signals : C.VIDEOComponent signals : Y/Pr/PbWhen component signals are used as the video inputsignals, the RGB card (AW-PB302) available as anoptional accessory must be installed in the convertiblecamera.5. Turn the menu setting control (R), and set the videooutput signals (displayed at the bottom right on the LCDpanel).It is not possible to set component signals (Y/Pr/Pb) forthe video output signals if composite signals (C.VIDEO)have been set as the video input signals.6. Select the next pan-tilt head system using theCONTROL/PREVIEW MONITOR OUT SEL button, andcontinue setting the video signals to be used for eachsystem concerned.SSIIGGNNAALL SSEELLEECCTTYY//PPrr//PPbb n CC..VVIIDDEEOOSSIIGGNNAALL SSEELLEECCTTCC..VVIIDDEEOO n CC..VVIIDDEEOOCCOONNTTRROOLLLLEERR SSEETTTTIINNGGn OOKK KKeeyyCONTROL/PREVIEW MONITOR OUT SELAUX1 2 3 4 5TALLYTRACING MEMORYLAMPMENULIMITOFFLIMITONFULLEMPTYOKLCDCONTRASTCAMERACONTROLSTARTPOINTR/BGAIN/PEDWHITEBAL AWCGAINMODECLOSE WIDE NEARDATA SETTR/PSET M.LOCKMEMORYIRISIRISIRISOPEN ZOOMTELE FOCUSFARCALLINCOMLEVELFOCUSOPENFARTELEOFFONOPERATEWIDEZOOM/FOCUS/IRISABCATWAB NGOKSTART/STOP RESTORE RESETDEF WIP H/F EXT ND OPTIONPAN/TILT SETCAMERA CONTROLTRACING/PRESET MEMORYIRISSPEEDPRIORITYFOCUSBARCAMTRPSETLOWHIGHAUTOMANUAUTOMANULOCK1 2 3 4 5 6 7 8 9 1011 12 13 14 15 16 17 18 19 2021 22 23 24 25 26 27 28 29 13031 32 33 34 35 36 37 38 39 4041 42 43 44 45 46 47 48 49 50DOWNPAN/TILT/FOCUS/IRISUPL RCLOSENEAR OPENFARCLOSENEAR2•3•4•52•3•4•523451CONTROL/PREVIEW MONITOR OUT SELAUX1 2 3 4 5TALLYTRACING MEMORYLAMPMENULIMITOFFLIMITONFULLEMPTYOKLCDCONTRASTCAMERACONTROLSTARTPOINTR/BGAIN/PEDWHITEBAL AWCGAINMODECLOSE WIDE NEARDATA SETTR/PSET M.LOCKMEMORYIRISIRISIRISOPEN ZOOMTELE FOCUSFARCALLINCOMLEVELFOCUSOPENFARTELEOFFONOPERATEWIDEZOOM/FOCUS/IRISABCATWAB NGOKSTART/STOP RESTORE RESETDEF WIP H/F EXT ND OPTIONPAN/TILT SETCAMERA CONTROLTRACING/PRESET MEMORYIRISSPEEDPRIORITYFOCUSBARCAMTRPSETLOWHIGHAUTOMANUAUTOMANULOCK1 2 3 4 5 6 7 8 9 1011 12 13 14 15 16 17 18 19 2021 22 23 24 25 26 27 28 29 13031 32 33 34 35 36 37 38 39 4041 42 43 44 45 46 47 48 49 50DOWNPAN/TILT/FOCUS/IRISUPL RCLOSENEAR OPENFARCLOSENEAR24 5 32 14. Set the left-most limit position in the travel range.1 Operate the PAN/TILT lever on the control panel torotate the camera to the position which is to serve asthe left-most limit position.2 While holding down the OK button, press button 44 .3 The setting is completed when the 41 [LIMIT ON]button’s lamp comes on.O To cancel the setting, press button 44 whilepressing the OK button again. When the setting iscanceled, the 50 [LIMIT OFF] button’s lamp comeson.5. Set the right-most limit position in the travel range.1 Operate the PAN/TILT lever on the control panel torotate the camera to the position which is to serve asthe right-most limit position.2 While holding down the OK button, press button 45 .3 The setting is completed when the 41 [LIMIT ON]button’s lamp comes on.O To cancel the setting, press button 45 whilepressing the OK button again. When the setting iscanceled, the 50 [LIMIT OFF] button’s lamp comeson.6. Select the next pan-tilt head system using theCONTROL/PREVIEW MONITOR OUT SEL button, andcontinue setting the travel range (limiters) for eachsystem concerned.
