14.G/LIN connector IN>This is the external sync signal input connector.This unit supports BBS (Black Burst Sync) and tri-levelsynchronization.Supply to this connector the signals that correspond to the videosignal format which has been set.Frequency: 59.94 Hz, 29.97 HzFormatExternal sync signal input formatTri‑level syncBBS2160/59.94p1080/59.94p720/59.94p1080/29.97p1080/59.94i1080/29.97PsF480/59.94i2160/29.97p―1080/59.94p1080/59.94p720/59.94p1080/59.94i―1080/29.97p―1080/29.97PsF―1080/23.98pover 59.94i―720/59.94p1080/59.94p720/59.94pFrequency: 50 Hz, 25 HzFormatExternal sync signal input formatTri‑level syncBBS2160/50p1080/50p720/50p1080/25p1080/50i1080/25PsF576/50i2160/25p―1080/50p1080/50p720/50p1080/50i―1080/25p―1080/25PsF―720/50p1080/50p720/50pFrequency: 24 HzFormatExternal sync signal input formatTri‑level sync2160/24p1080/24p1080/24PsF1080/24pFrequency: 23.98 HzFormatExternal sync signal input formatTri‑level sync2160/23.98p1080/23.98p1080/23.98PsF1080/23.98p1080/23.98PsF15.DCIN connector <12VIN> (XLR connector)Input 12V DC.•Use a DC cable with the following lengths.For 12V input: Max. 3m (9.84ft) (when using an AWG16 cable)External DC power supplyConnect after making sure that the output voltage of the external DCpower supply is compatible with the rated voltage of the camera.Select an output amperage for the external DC power supply with amargin above the total amperage of the connected devices.The total amperage of connected devices can be calculated with thefollowing formula.Total power consumption ÷ voltageWhen the power of the camera is turned on, inrush current is generated.Insufficient power supply when turning on the power may cause amalfunction. We recommend that you use an external DC power supplythat can assure double the capacity of the total power consumption of thecamera and connected devices that are turned on by interlock when thepower of the camera is turned on (such as lenses, wireless microphonereceivers).•Make sure of the pin alignment of the DC output terminal of theexternal DC power supply and the camera DC IN connector, andconnect the polarity correctly.If the +12V power supply is mistakenly connected to the GND terminal,it may cause fire or malfunction.12VIN12341GND2—3—4+12VHA16RA-4P (77)Hirose Electric Co.16.IRID switches CAM1CAM2CAM3CAM4These are used to select the ID of the wireless remote control(optional accessory). (→page24)The IR ID switch settings “CAM1” to “CAM4” correspond to the to buttons on the wireless remote control.17.Ground connectorConnects to the ground connector on a wall outlet, ground bar, etc.for grounding. (→page6)18.AUDIO IN connector Inputs external audio (microphone, line).19.Ventilation holesBlocking the ventilation holes may cause a malfunction. Make surethere is sufficient space around the ventilation holes.20.MONITOROUT connector OUT>This is an SDI video signal output connector. Use it in applicationssuch as displaying the crop position when cropping from 4K to HDand for monitoring images.21.12G SDI OUT connector <12G SDI OUT>This is a 12G-SDI video signal output connector.22.Optical connector This is the connector for the SFP+ optical fiber module. By connectingthe optional fiber module, it is possible to output signals converted tooptical signals from SDI signals. Select the fiber module that suits thesignal band*1for each format.*1•4K (59.94p, 50p): 12G•4K (other than 59.94p, 50p): 6G•HD (59.94p, 50p): 3G•HD (other than 59.94p, 50p): 1.5G•This unit does not support input by optical signals.23.Tripod screw holes(Screw: 1/4-20 UNC, ISO 1222 [6.35mm (1/4inches)])Use these screw holes when securing the unit to a tripod, etc.17Parts and their functions(continued)
